Contact Us

CD4021BE

Brand: Texas Instruments
Texas Instruments CD4021BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4021BE — Power Management & Signal Chain | Superb Automation

CD4021BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4021BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4021BE: an 8-stage static shift register in a 16-lead plastic DIP

CD4021BE is the through-hole member of the CD4021B family, an 8-stage static shift register with serial and parallel inputs in a 16-lead plastic DIP, 25 pieces to a tube. The vendor descriptor reads CMOS 8-Stage Static Shift Register, the document is the CD4014B and CD4021B data sheet revision C, and the feature line gives a 12 MHz typical clock rate at 10 V, eight master slave flip-flops with output buffering and control gating, a quiescent current tested to maximum at 20 V, 5 V, 10 V and 15 V parametric ratings, and JEDEC 13B conformance.

The addendum lists CD4021BE as Active in production, PDIP (N) with 16 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4021BE. The same document carries CD4021BM as an obsolete SOIC tube row, CD4021BM96 as the active SOIC reel at 2500 pieces and CD4021BPWR as the active TSSOP reel at 2000 pieces with the marking CM021B, so the plastic DIP and the two reels are the formats a buyer can still order.

The CD4021BE row as the vendor addendum publishes it

Part class8-stage static shift register, serial and parallel inputs
Vendor descriptorCMOS 8-Stage Static Shift Register
Vendor documentCD4014B and CD4021B data sheet revision C
Clock rate, vendor feature line12 MHz typical at 10 V
StagesEight master slave flip-flops with buffered outputs
InputsSerial data, eight parallel data, parallel or serial control, clock
OutputsThree stage outputs brought out plus the serial output
Supply range3 V to 18 V
Parametric ratings5 V, 10 V and 15 V tables
Output drive, parametric table4.2 mA sink and source
Output typePush pull, balanced outputs
Input current, maximum1 microamp at 18 V over the full range, 100 nA at 25 degrees
Quiescent currentTested to maximum at 20 V on every unit
Package for this codePDIP (N), 16 leads
Packing25 pieces in a tube
Lead finishNIPDAU
Moisture levelNot applicable for this package type
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4021BE
SOIC memberCD4021BM 50 piece tube, CD4021BM96 2500 piece reel
SOIC reel rowCD4021BM96, 2500 pieces, marking CD4021BM
Obsolete SOIC tube rowCD4021BM, quantity blank, Call TI
TSSOP rowCD4021BPWR, 2000 pieces, marking CM021B

Reading eight switches into one input

The classic use of this part is a bank of eight DIP switches or eight panel switches read by a single microcontroller input. The eight switches connect to the parallel inputs, the parallel or serial control pin is pulsed to load them, and the eight bits then shift out on the serial output one clock at a time. The whole interface costs three microcontroller pins instead of eight, and the register holds the switch state statically, so the reading does not decay between scans.

The parallel load is asynchronous, which is the detail that catches people out. When the control pin goes to the load state the register takes the parallel inputs immediately rather than on a clock edge, so the switch levels must be stable before the load pulse and must stay stable through it. A switch with a 100 nF capacitor for debounce and a 100 k pull resistor settles in about 10 ms, which is long compared with the load pulse but short compared with a scan interval.

Static, cascadable, and slow enough to be forgiving

The register is static, so the clock can stop at any point and the contents stay. The serial output feeds the serial input of the next package, which chains two registers into sixteen stages with no external logic, and the 12 MHz typical clock rate at 10 V means a chain of four packages still shifts 32 bits in about 11 microseconds. At 5 V the clock rate is lower and the vendor does not print the figure in text, so a 5 V chain should carry margin rather than assume the 10 V number.

The output drive in the parametric table is 4.2 mA rather than the 6.8 mA of the gate parts, which is a reminder that this is a register and not a driver. Driving an LED directly is marginal at best, and driving a long cable is outside what the part is for. The three stage outputs that are brought out exist so a shorter shift path can be taken without clocking all eight stages, which saves time in a chain that only needs the first few bits.

The control pins and the states that must not float

Three pins decide what the register does: the clock, the parallel or serial control, and the serial data input. All three need defined levels. A floating control pin can leave the part in a state where a clock edge loads parallel data instead of shifting, which produces a register that appears to shift incorrectly at random. A 100 k resistor to ground on the control pin holds it in the shift mode at power up, and the same value on the serial data input defines the first bit that enters an unloaded register.

Because the parallel inputs are also CMOS inputs, eight switch lines mean eight more pins that must not float. A switch that is open leaves its input floating unless a pull resistor is fitted, and the register then shifts a level that depends on the board rather than on the switch. Eight pull resistors are part of the circuit, not an optional extra.

Where the 4021 sits against the 4014 and the 4094

The CD4014B shares the document and is the same eight stage register with a different input arrangement: it has a single parallel or serial control but brings out fewer stage outputs, which suits a pure serial chain rather than a part parallel read. The CD4094B is the other direction, a serial in parallel out register with a strobe output that latches the parallel data, which is the part to use when the register drives eight outputs rather than reading eight inputs.

A board that reads inputs takes the 4021, a board that drives outputs takes the 4094, and a board that does both takes one of each. The 4021 remains the cheapest way to turn eight switch lines into one serial stream without a program beyond the shift routine.

Incoming checks on a shift register

The functional check is a load, a shift and a compare: load a known pattern on the parallel inputs, shift it out, and confirm the bit order matches the data sheet rather than the order that seems obvious. The second check is the serial input path, which is a separate pin and a separate failure mode. The body marking distinguishes the DIP from the SOIC, and the ceramics carry a different finish and screening route.

The reference pages are the incoming inspection plan, date code management, and the pin to pin cross reference when a legacy board needs a second source for the register.

Questions that come up on the 4021

Whether the register can be clocked continuously with the control pin in the load state. It can, and the parallel inputs are then transferred on every clock, which is a way to sample a bus rather than to shift it.

Whether two registers can be chained. They can, with the serial output of the first feeding the serial input of the second and both clocks tied together.

Whether the eight switches need debounce capacitors. They need pull resistors at minimum, and a capacitor per switch if the reading is taken during a mechanical transition.

Whether the part can drive a seven segment display. It cannot, because 4.2 mA and a serial output are not a segment driver, and a display needs a decoder and a driver stage.