Contact Us

CD4013BE

Brand: Texas Instruments
Texas Instruments CD4013BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4013BE — Power Management & Signal Chain | Superb Automation

CD4013BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4013BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4013BE: two D-type flip-flops with set and reset in a 14-lead DIP

CD4013BE is the plastic dual-in-line member of the CD4013B family, two independent D-type flip-flops with separate data, set, reset and clock inputs and complementary outputs, on the 3 V to 18 V CMOS process. The vendor descriptor is CMOS Dual D-Type Flip Flop, the document is the CD4013B data sheet revision E, and the parametric table gives two channels, a 24 MHz maximum clock frequency, 6.8 mA sink and source, a 600 microamp maximum supply current and standard speed with propagation above 50 ns. Each flip-flop transfers the level on its data input to the output on the rising clock edge, and set and reset act independently of the clock.

The addendum lists CD4013BE as Active in production, PDIP (N) with 14 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4013BE. The same document carries CD4013BM at 50 to a tube, CD4013BM96 at 2500 to a reel, CD4013BNSR at 2000 to a reel and CD4013BPWR at 2000 to a reel, so the die is available in four bodies, and the two flip-flops inside are identical in every one of them.

The CD4013BE row as the vendor addendum publishes it

Part classDual D-type flip-flop with independent set and reset
Vendor descriptorCMOS Dual D-Type Flip Flop
Vendor documentCD4013B data sheet revision E
Supply range3 V to 18 V
ChannelsTwo, each with data, clock, set, reset and Q and Q bar outputs
Clock frequency, parametric table24 MHz maximum
Toggle rate, vendor feature line16 MHz typical at 10 V
Output drive, parametric table6.8 mA sink and source
Supply current, maximum600 microamps
Output typePush pull, balanced outputs
Input typeStandard CMOS
Package for this codePDIP (N), 14 leads
Packing25 pieces in a tube
Lead finishNIPDAU
Moisture levelNot applicable for this package type
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4013BE
Same string in the addendumCD4013BE.A and CD4013BEE4, both 25 piece tube
SOIC memberCD4013BM 50 piece tube, CD4013BM96 2500 piece reel
SOP and TSSOP membersCD4013BNSR and CD4013BPWR, both 2000 piece reels
Ceramic rowsCD4013BF and CD4013BF3A with the wide screening

Divide by two, debounce and capture: the three jobs this part does

The first job is division. Connecting the Q bar output back to the data input makes the flip-flop toggle on every clock edge, which halves the input frequency with a 50 per cent duty cycle that no resistor capacitor network can match. Two flip-flops in one package divide by four, and chaining packages divides further, which is why the 4013 appears in clock dividers built long before any microcontroller was cheap enough to do the same job in software.

The second job is contact debounce. A switch feeds the clock input, the data input is tied to the supply through a resistor, and the flip-flop captures the first edge and ignores the bounce behind it, because the clock input responds to a transition rather than to a level. The outputs then change once per press, which is the behaviour a counter or an interrupt input needs.

The third job is data capture, usually of an alarm or a fault flag that must be held after the event has passed. Set and reset act independently of the clock, so a fault can force the output without a clock edge, and the clock can then be used to clear the flag on the next cycle. That independence is also the part's main hazard: an unconnected set or reset pin floats at an undefined level on a CMOS input and can sit at half the rail, drawing cross current and leaving the output in an indeterminate state.

The clock number, and why 24 MHz and 16 MHz are both printed

The parametric table lists a 24 MHz maximum clock frequency, while the feature line in the vendor document says 16 MHz typical toggle rate at 10 V. The two are not the same measurement. The feature line describes a typical toggle rate observed at a 10 V rail, and the parametric maximum is the limit the part is specified against, which is normally taken at the highest rated supply and with a defined load. A timing budget should work from the maximum with margin, and a circuit that runs a 4013 at 20 MHz on a 5 V rail is outside the region where either number was measured.

At 5 V the part is slower than at 10 V, and the vendor does not print a 5 V clock figure on the product page. The practical rule is that a 4013 clocked at a few hundred kilohertz, which covers debounce, slow counters and divide by two chains, is far inside the part's capability, and a 4013 used as a fast prescaler is at the edge of what the family was built for. A circuit that needs 50 MHz takes a 74HC or a 74AC flip-flop, at the cost of the 18 V supply range.

Set, reset and the state that must not float

Four pins per flip-flop are asynchronous in this part and every one of them has to be at a defined level at power up. Set and reset are active high, and both being high at once puts both outputs high, which is a state the data sheet defines but a circuit rarely wants. A 100 k resistor to ground on set and reset is enough to hold them low over the full temperature range, because the input leakage is 1 microamp at 18 V and 125 degrees and 100 k drops 0.1 V at that current.

The data input is equally important. A floating data input picks up noise from the clock line and the flip-flop then captures a random level, which looks like an intermittent fault that moves when a hand comes near the board. The rule for this family is that every input is tied to a rail through a resistor, and the 4013 has five inputs per flip-flop, which is the most of any gate in the CD4000B set.

Where the 4013 sits against the 4027

The CD4027B is the JK member of the same family, also two flip-flops in a 16-lead body, with the same 16 MHz typical toggle rate at 10 V and independent set and reset. The difference is the input structure: a JK flip-flop takes J and K and defines the toggle state internally, while a D flip-flop needs the Q bar feedback wired externally to toggle. For a divide by two the D part needs one wire and the JK part needs both inputs tied high, and for a circuit where the toggle condition is a logic term the JK part saves gates.

The D part wins where the input is data rather than a condition, because a single data input with a clock is easier to drive from a comparator or a sensor than two inputs with a steering table. In a bill of materials that already carries the 4013, adding a 4027 for a toggle function usually costs more than wiring the 4013 back to itself.

Incoming checks before the part goes on a board

The function test for a 4013 is a clock, a data pattern and a set and a reset, which is a four step check per flip-flop. The set and reset test is the one that matters most, because a part with a weak set input tests perfectly in a toggle circuit and fails in the circuit that uses set as an alarm latch. The body marking distinguishes the plastic DIP from the SOIC, and the ceramic rows carry a different finish and screening route.

The reference pages are the incoming inspection plan, the pin to pin cross reference for the second source question, and date code management for the traceability rule on a part that has been in catalogues for four decades.

Questions that come up on the 4013

Whether both flip-flops share a clock. They do not; each has its own clock pin, which is what allows one package to divide two unrelated signals.

Whether the outputs can drive a small relay directly. They cannot, because 6.8 mA is below a relay coil current, and the output needs a transistor and a suppression diode.

Whether the part can be used as a power-on reset. It can, with an RC network on the set or reset pin, provided the RC is sized against the 1 microamp leakage at the top of the temperature range.

Whether the DIP body is suitable for a new build. It is suitable for hand assembly and repair, and a reflow build should use the BM96 or the PWR row instead, with the same die and the same electrical numbers.