CD40110BE
Product Specifications
CD40110BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD40110BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD40110BE: the up down counter with a seven segment driver in a plastic DIP
The CD40110BE is the plastic dual in line entry for the CD40110B, a dual clocked up and down counter with a latch, a decoder and a seven segment bipolar output driver on one die, in a 16-lead body. The vendor page lists the device as ACTIVE with a counter function, seven bits, a standard CMOS input, a push pull output and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD40110BE.
This is the part that replaces a counter, a latch, a decoder and a display driver with one package. The output stage can source up to 25 mA per segment, which drives a common cathode light emitting display directly, and the carry and borrow outputs can be tied to the clock inputs of the next package so a multi digit counter needs no external logic. That cascade is the reason the part appears in panel meters and in counting scales where a microcontroller would be more expensive than the logic.
The CD40110B rows as the addendum publishes them
| Part class | Up down counter, latch, decoder and seven segment driver |
| Vendor descriptor | Counter, 7 bit, 25 mA segment drive |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS097 or later revision, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Output source current | Up to 25 mA per segment |
| Clock inputs | Separate clock up and clock down lines |
| Clock preconditioning | Either clock works regardless of the other, within 100 ns typical |
| Carry and borrow | Short negative pulse at the 9 to 0 and 0 to 9 transitions |
| Latch | Strobe holds a count while the counter keeps clocking |
| Cascade | Carry and borrow drive the next package directly |
| Input current | 1 microamp at 18 V over temperature, 100 nA at 25 degrees |
| PDIP body | 16 leads, 181.42 square millimetres, 19.3 by 9.4 mm |
| PDIP rows | CD40110BE and CD40110BE.A, 25 pieces, Active |
| Other plastic bodies | None published in the current addendum |
| Ceramic body | Described in the data sheet, not in the current addendum |
| Chip form | H suffix described in the data sheet, not in the current addendum |
| Related device | CD4518B dual BCD up counter without the display drive |
| Related driver | CD4511B BCD to seven segment driver without the counter |
| Display type | Common cathode, driven directly |
| Segment current setting | Series resistor per segment, external |
Only two rows are live and both are the plastic DIP. That is the narrowest availability in this group. The data sheet describes ceramic bodies with D and F suffixes and a chip form with an H suffix, but the current addendum does not publish them, so a customer who needs a wide temperature version has to ask for a special rather than point at a row. The two live rows differ only by the .A suffix and share a marking.
What the counter and the driver do together
The clock inputs are separate for up and down, and the vendor states that either can be clocked regardless of the state or timing of the other within 100 ns typical. That preconditioning is what allows two independent sensor streams, one adding and one subtracting, to drive the same counter without an external direction logic. A quadrature encoder with two phases can be decoded externally and fed into the two clocks, and a simple up down switch can do the same by hand.
The latch is separate from the counter. A strobe holds a count on the display while the counter continues to clock, which is what a weighing scale or a rate meter needs: the display updates when the operator asks and not while the number is moving. The decoder feeds a seven segment bipolar driver that sources up to 25 mA, so the segment current is set by the series resistors rather than by the driver.
The carry and borrow outputs are short negative pulses, one at the nine to zero transition and one at the zero to nine transition, and they can drive the next package's clock inputs directly. A four digit counter is four packages in a row with three wires between them and no glue logic, which is the whole argument for this part against a microcontroller on a board with no code.
Where the plastic DIP is the right choice
At 181.42 square millimetres the plastic DIP is the only body available, so the choice is not between packages but between this part and a different architecture. A display board that is repaired in the field takes a socket and a 25 piece tube, and a counting scale that is built in the hundreds takes the same tube. The absence of a surface mount body is a real limit for a dense board, and it is the reason many newer boards use the CD4518B counter with a separate CD4511B driver on the same board instead.
The thermal side matters more here than on a gate. Seven segments at 13 mA each is about 90 mA of source current, and the voltage drop across the output stage turns part of that into heat inside a 16-lead plastic package. The junction temperature rise is small but not zero, and a display that runs at full brightness in a hot enclosure should be checked rather than assumed.
Multiplexing is the other way this part is used. Several counters can share one display if the segment lines are common and the digit lines are switched, but the current per segment has to rise to keep the average brightness, and the 25 mA source limit is reached before a large display is bright. A board that multiplexes four digits at a quarter duty needs about four times the segment current, which is at the top of the rating, and the thermal check that follows is the one that decides whether the plastic package is adequate.
The .A row is a separate orderable entry with the same marking and the same body. A buyer who has to keep a documented part number on a drawing should name the row rather than the family, because a distributor will ship whichever row the system selects and both will work on the bench. That is harmless for a new build and it is not harmless for a customer who has to show a traceable part number to an auditor.
What the documents do not publish
The page does not print the segment saturation voltage, the maximum blanking or latch frequency, or the current drawn by the carry output. Those are in the data sheet. The page also does not print the pin out, and for a 16-lead part with two clocks, a latch, a reset and seven segment outputs the pin out is the wiring specification rather than a detail.
Second source and long term availability
The CD40110B is second sourced under the same number by a small number of vendors and the plastic DIP is the only live row, which makes it a part to watch. A functionally similar route is the CD4518B counter with the CD4511B driver, two packages instead of one and a different board. The component obsolescence management page covers how a single source part is monitored, and the last time buy and LTB planning page covers how a final order is sized.
What to send with an enquiry
Send the string, the display type, the segment current and the quantity. The current decides whether the driver is inside its rating and the display type decides the polarity. If the board needs more than four digits, say so, because the cascade is wired package to package and the carry pulse width limits the chain length. The kitting service page explains how the counter, the display and the segment resistors are picked as one kit.