Contact Us

CC2520RHDR

Brand: Texas Instruments
Texas Instruments CC2520RHDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC2520RHDR — Power Management & Signal Chain | Superb Automation

CC2520RHDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC2520RHDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC2520RHDR: 2.4 GHz IEEE 802.15.4 RF Transceiver

CC2520RHDR is a 2.4 GHz IEEE 802.15.4 radio transceiver for low power networks in a 28-pin QFN body of 28 pins. It runs 250 kbps at 2 MChip/s from 1.8 V to 3.8 V, holds about 400 m of line of sight range, and hands the packet framing to the radio so the host controller only moves bytes.

Order code and package

Ordering stringCC2520RHDR, QFN-28 (RHD), 5 mm by 5 mm, exposed pad
Supply1.8 V to 3.8 V
Temperature-40 C to +125 C
Air interfaceIEEE 802.15.4 at 2.4 GHz, 250 kbps, 2 MChip/s
Host interfaceSPI with FIFOs, plus GPIO for frame and control signals
Supporthardware CSMA/CA and AES-128 for the host processor

Electrical parameters that decide the application

Radio bit rate250 kbps
Chip rate2.0 MChip/s
Adjacent channel rejection49 dB
Alternate channel rejection54 dB
Output powerup to 5 dBm
Line of sight rangeabout 400 m
LPM2 to active0.3 ms including regulator start
LPM1 to active0.2 ms, crystal start only
RX to TX turnaround192 us
Logic high input80 percent of VDD, 30 percent for a low

Points to check before this part goes on a BOM

Two megachips a second carrying 250 kbps is eight chips per bit, a spreading gain of 9 dB, and that gain is why a 2.4 GHz link survives next to a Wi-Fi access point. It is also why the adjacent channel rejection of 49 dB matters more than the sensitivity number: the interferer is usually a nearby transmitter, not a distant one.

Turnaround is 192 us in both directions, which at 250 kbps is six byte times. A protocol that alternates transmit and receive for every packet therefore spends 384 us per exchange in transition, so an acknowledgement scheme with 20 byte payloads is spending more time turning around than sending.

The I/O thresholds are 80 percent and 30 percent of VDD, so at a 1.8 V supply a host running at 1.8 V needs 1.44 V for a high level, which most 1.8 V logic provides, while at 3.8 V the same host cannot reach the threshold and needs a level shifter. The logic supply is the part of this device that changes with the battery, not the radio.

Wake from LPM2 is 0.3 ms because the internal regulator has to start before the crystal, and LPM1 is 0.2 ms because only the crystal starts. A sensor node waking once a second to listen saves 0.1 ms per cycle by staying in LPM1, which is 0.01 percent of the time and worth nothing; the same node waking every 10 ms saves 1 percent and is worth doing.

The 5 dBm output and the 400 m range belong to the same sentence only outdoors. Indoors, a 2.4 GHz link loses roughly 30 dB crossing two walls, which is a factor of a thousand in power and takes the range from 400 m to about 12 m, so the range figure is a starting point and not a specification.

The crystal and its load capacitors sit next to the part, and at 2.4 GHz the four component matching network is tuned to the board it was measured on, so the same network on a different stack up needs re-tuning. A radio that passes on the bench and fails inside a metal enclosure is usually the antenna and the ground plane rather than the transceiver.

The 5 dBm at the pin is measured before the balun and the harmonic filter, and the 2.4 GHz band is shared with Wi-Fi and Bluetooth. A second harmonic at 4.8 GHz that reaches a nearby receiver is the usual reason a link that passes a conducted test fails in the field, which makes the filter part of the specification and not an optional extra.

Where this order code fits

Building automation, smart metering, sensor networks and industrial telemetry use this part where a host processor needs a standards compliant 2.4 GHz link with the timing work done in hardware. A meter that reports once an hour and a building controller that polls every 100 ms use the same radio with different duty cycles, and the hardware CSMA/CA is what keeps the second case from colliding with a neighbour's network on the same channel. The vendor reference files are part of the qualification: a change of balun or filter is a change of radio even when the transceiver order code has not moved, and the test report has to be repeated for the new network. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the One Stop RF Supply page.

Questions buyers ask

Does it need a host to run the protocol? Yes for the network layer. The radio handles framing, CSMA/CA and encryption support, and the host runs the stack, so the part is a transceiver and not a system on chip.

What supply range does it accept? 1.8 V to 3.8 V, which covers two alkaline cells fresh and a single lithium cell, but the logic levels follow the supply so the host has to match or be shifted.

Is the 400 m range realistic indoors? No. Two walls cost about 30 dB, which shortens the link to a few tens of metres; the 400 m figure is open air line of sight.

How much does the crystal matter? It sets the channel accuracy. The radio channel spacing at 2.4 GHz is 5 MHz, so a 40 ppm crystal at 2440 MHz moves 98 kHz, which is small against the spacing but large against the 2 MHz occupied band.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.