Contact Us

CC1310F128RSMR

Brand: Texas Instruments
Texas Instruments CC1310F128RSMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC1310F128RSMR — Power Management & Signal Chain | Superb Automation

CC1310F128RSMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC1310F128RSMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC1310F128RSMR: the same radio in a 4 mm body with ten pins

CC1310F128RSMR is the 4 mm by 4 mm VQFN32 member of the CC1310 family, with 128 kilobytes of flash and 10 general purpose input output pins. It is the same die as the 7 mm body, with the same Cortex-M3 core, the same sensor controller and the same radio, in a package that occupies a third of the area and brings out a third of the pins.

The trade is simple to state and hard to live with. A 4 mm package fits inside a sensor housing, a tag or an implantable style module where a 7 mm part does not. It also gives the firmware ten pins for everything: the radio control lines, the debug port, the sensor interface and any indicator. A node that needs a display, an external flash and two serial ports is not a candidate.

The RSM body is the reason this string exists separately from the RGZ string. Both are F128 parts, both run the same SDK, and both have the same electrical specification. A buyer comparing them sees one number that matters and one that does not: the pin count matters, the package area matters, and the radio performance is identical.

What stays the same and what does not

The supply range stays at 1.8 V to 3.8 V. The receive current stays at 5.4 mA and the transmit current at plus 10 dBm stays at 13.4 mA. Sensitivity in long range mode stays at minus 124 dBm at 50 kbps, selectivity stays at 56 dB in 100 kHz and blocking stays at 90 dB at 10 MHz.

The flash stays at 128 kilobytes and the SRAM stays at 8 kilobytes of cache plus 20 kilobytes of ultra low leakage. The sensor controller stays at 16 bits with its own 2 kilobytes.

What changes is the number of accessible peripherals and the thermal path. The 4 mm body has a higher junction to ambient thermal resistance, which matters when the radio transmits at plus 15 dBm continuously, and a lower pin count, which matters always. The document prints the thermal table per package for exactly this reason.

Functionsub 1 GHz wireless microcontroller
CoreArm Cortex-M3 at 48 MHz
Flash128 kilobytes
SRAM8 kilobytes of cache plus 20 kilobytes of ultra low leakage
Sensor controller16 bit, autonomous, 2 kilobytes of SRAM
Radiosub 1 GHz, 2-FSK, GFSK, OOK and 802.15.4g
Sensitivityminus 124 dBm long range at 50 kbps
Output powerup to plus 15 dBm
Receive current5.4 mA
Transmit current13.4 mA at plus 10 dBm
Standby current0.7 microamps with RAM retained
ADC12 bit, 200 thousand samples per second
Supply range1.8 V to 3.8 V
PackageVQFN, RSM body, 32 pins, 4 mm by 4 mm, 10 general purpose pins
Carrierlarge tape and reel
Debug2 pin cJTAG

Ten pins, honestly counted

The debug port takes two pins and they are not optional on a first build. The radio needs no external control lines in the default configuration, because the RF core is programmed through the same register interface as the rest of the device. That leaves eight pins for the application, which is enough for one SPI port, one UART, two analog inputs and one interrupt.

A tag that measures temperature and acceleration, reports once a minute and blinks an LED fits in that budget. A node that also has to drive a segment display does not, and the honest answer is the RGZ body rather than a port expander, because an expander adds a part, a pin and a failure mode to save three millimetres of package.

The 2 pin cJTAG is worth calling out because it is the reason the debug budget is affordable at all. A full JTAG header on a 10 pin part would consume a fifth of the available pins, and cJTAG makes the same debug access available on two.

The thermal difference is real at high output power

At plus 15 dBm the radio draws roughly 25 mA, most of which is the power amplifier, and the die dissipates a few hundred milliwatts in bursts. In a 4 mm package with a small thermal pad the junction rises faster than in the 7 mm package, and a node that transmits for a long duty cycle in a sealed housing can reach its limit.

That is not a reason to avoid the part. It is a reason to compute the duty cycle and the thermal resistance rather than assume them. A sensor that transmits for 20 milliseconds once a minute has a duty cycle of 0.03 percent, and the thermal time constant of the package is much longer than the burst.

A repeater or a gateway that transmits continuously is a different case, and there the 7 mm body with more copper is the better answer.

Where the small body fits

The document lists the same applications as the rest of the family: smart utility networks, wireless M-Bus, building automation, metering, alarm and security, and long range sensor networks. The small body narrows that list to the nodes that have no display and no external memory.

Utility metering is the largest use, in the sub-metering role: a pulse counter on a water meter, a current transformer clamp on a branch circuit, a temperature probe on a pipe. Those nodes report a number and nothing else, and the 4 mm package with 10 pins is more than enough.

Asset tracking is the second use. A tag on a pallet or a tool needs a radio, a battery and an accelerometer, and it has to fit in a housing that is glued to the asset. 4 mm by 4 mm is the difference between a tag that fits and a tag that does not.

Wearable and medical telemetry is the third, with a caveat. The small body fits a patch, and the radio reaches across a room, but a patient connected product needs its own qualification and the module around it is usually the certified item. In that arrangement this part is a component inside somebody else's certified module, and the traceability that matters is the module maker's, not ours.

Our MCU cross reference page lists the wireless families by package and pin count, and the pin to pin cross reference page describes how we check whether a smaller body can take the place of a larger one without a board change.

The clock and the RF port are the two places where the small body costs engineering time rather than pins. The RF port is single ended on this family, which removes the balun but puts the matching network directly against the package pin, and the 4 mm body leaves less room for the filter before the antenna. On a tag with an integrated antenna that is a tight space, and the matching values have to be tuned on the actual mechanical sample rather than on a development board.

The second is the crystal. A 32 kHz crystal for the real time clock is optional and it costs two pins, which on a ten pin part is a fifth of the budget. A product that needs accurate timekeeping across sleep has to spend those pins, and a product that can wake on an internal timer does not.

That makes the small body a deliberate choice for a product that will never grow. A platform that expects to add a display later should start on the larger body, because moving later means a new board, new antenna tuning and a new thermal check.

Three questions buyers ask about this string

Is it the same silicon as the 7 mm part? Yes, same die, different package and different bonding.

Can it drive an LCD? Not directly, and not with 10 pins. That job belongs to the larger body.

Is the 15 dBm output available in this body? Yes, and the thermal table is the limit rather than the radio.