Contact Us

CC1020RSSR

Brand: Texas Instruments
Texas Instruments CC1020RSSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC1020RSSR — Power Management & Signal Chain | Superb Automation

CC1020RSSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC1020RSSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC1020RSSR: a narrowband transceiver for the 12.5 kHz channel world

CC1020RSSR is a single chip UHF transceiver for narrowband systems. It covers 402 to 470 MHz and 804 to 930 MHz, it handles OOK, FSK and GFSK at up to 153.6 kBaud, and it reaches minus 118 dBm sensitivity in a 12.5 kHz channel. The RSSR suffix is the 32 pin QFN body on a large reel.

Narrowband is the word that decides where this part belongs. A 12.5 kHz channel is the spacing used by licensed land mobile radio and by automatic meter reading in bands where the regulator allows only a sliver of spectrum per device. In that world a receiver that is 10 dB deaf is a receiver that does not work at the edge of its coverage, and the sensitivity figure matters more than the data rate.

The device is a low intermediate frequency architecture with an image rejection mixer, which is why it needs no external IF filter and why the external component count is small. A programmable frequency synthesizer and automatic frequency control let the part operate with a low cost crystal instead of a temperature compensated oscillator, and the digital RSSI and carrier sense outputs give the firmware what it needs to decide whether the channel is clear.

Every figure here is from SWRS046I, revised September 2018, and from the package addendum. The document also carries a sentence that a buyer should read before specifying this part into a new product, and it appears in the description rather than in a footnote.

The successor sentence in the description

The vendor recommends the CC1120 as the successor of the CC1020 for new RF work. That is not a discontinuation notice, and the part is still in production, but it is the sort of sentence that decides a lifecycle argument. A product with a ten year life that starts now should either use the successor or accept that the silicon is on the far side of its curve.

For an existing product the calculation is different. A meter reading module that has been in the field for eight years, with a certification that names this exact part, does not want a new radio. It wants the same radio, on the same reel, with the same register settings. That is where this string in our catalogue earns its place: not as a new product choice, but as a supply of a part that is still needed.

Functionsingle chip UHF transceiver, narrowband
Frequency range402 to 470 MHz and 804 to 930 MHz
Channel spacing12.5 kHz and 25 kHz
ModulationOOK, FSK and GFSK
Data rateup to 153.6 kBaud
Sensitivityminus 118 dBm in a 12.5 kHz channel
Receiver current19.9 mA in receive
Supply range2.3 V to 3.6 V
Architecturelow IF with image rejection mixer
External filternone required
Synthesizerprogrammable, with automatic frequency control
Indicatorsdigital RSSI and carrier sense
Bit synchronizerintegrated
Configurationserial bus, register based
StandardsEN 300 220, FCC part 15, ARIB STD-T67
PackageQFN, 32 pins
Carrierlarge tape and reel
Recommended successorCC1120 for new work

Why 12.5 kHz is harder than it looks

A narrow channel means a narrow filter, and a narrow filter means the crystal has to be accurate. The offset between the transmitter and the receiver in a low cost system is dominated by crystal tolerance, and at 12.5 kHz spacing a 20 ppm crystal at 868 MHz is already 17 kHz of error. That is more than the channel.

Automatic frequency control is the answer, and it is the reason this part can work without a temperature compensated oscillator. The receiver measures the frequency error on the preamble and pulls the local oscillator onto the carrier, which makes a 20 ppm crystal behave like a much better one. The document describes the AFC loop and the register settings that control its range and speed.

The second consequence is that the data rate cannot be high. A 12.5 kHz channel with a 153.6 kBaud setting is a theoretical maximum, not a practical one; the useful rates are in the low tens of kilobaud, and at those rates the packet is short enough that the preamble overhead is a real fraction of the airtime.

Where narrowband still pays

The document lists automatic meter reading, wireless alarm and security systems, home automation, low power telemetry, and the ISM and short range device bands at 402, 424, 426, 429, 433, 447, 449, 469, 868 and 915 MHz. The list is a snapshot of the 2006 market and most of it has moved to 2.4 GHz or to LoRa style spread spectrum.

The segments that did not move are the ones with a licensed channel and a coverage requirement: utility meters in a band where the regulator gives each concentrator a slice, alarm panels that have to reach a basement, and telemetry in a plant where the spectrum is already allocated. In those systems the link budget is the product, and a receiver that hears minus 118 dBm at 12.5 kHz is worth more than a radio that hears minus 100 dBm at 500 kHz.

Our obsolete RF part replacement page covers what we do when a part like this one is on allocation, and the RF component sourcing page describes the traceability we keep for RF lots.

What to check before buying a reel

The register configuration is the first item. This part is programmed entirely through a serial bus, and a configuration that was tuned for one board will not necessarily work on another. A reel bought from a broker often comes without the configuration file, and the buyer then has to recover the settings from a working unit.

The second is the crystal. The part is specified with a reference frequency and a tolerance, and a board that was built with a cheaper crystal may not meet the sensitivity figure even though the radio is fine.

The third is the date code. A part that has been in a warehouse since 2012 may still work, but the solderability of the lead finish is not indefinite, and the moisture level in the addendum tells you how it should have been stored.

The fourth is the matching network. The 32 pin QFN brings the differential RF pins out on one side, and the balun and the harmonic filter are external. A reel without the vendor's reference values is not a problem, because the document prints them, but a board whose matching was tuned for a different band does need the values reworked before the compliance test.

One more practical point on the high band. The 804 to 930 MHz range overlaps the 868 MHz European band and the 915 MHz American band, and the two have different duty cycle rules. The same hardware can serve both, and the firmware that decides when to transmit has to know which rule applies. That is a certification question rather than a component question, and it is cheaper to settle before the first build than after.

The last thing to check is the antenna port. The device presents a differential RF interface and the balun is external, so the matching network and the antenna are part of the radio rather than part of the module. A board that changes the antenna for a smaller housing changes the match, and at 12.5 kHz spacing a 3 dB loss is a visible reduction in coverage.

Three questions buyers ask about this string

Is it still in production? Yes according to the document, with the caveat that the vendor names a successor for new work.

Can it do 500 kBaud? No. 153.6 kBaud is the printed maximum, and at that rate the channel is no longer narrowband.

Does it need an external PA? For the 10 dBm class of link, no. For a longer link the document shows the recommended arrangement with an external amplifier.