Contact Us

BQ771824DPJR

Brand: Texas Instruments
Texas Instruments BQ771824DPJR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ771824DPJR — Power Management & Signal Chain | Superb Automation

BQ771824DPJR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ771824DPJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ771824DPJR: the 3.850 V option for a three series pack

The BQ771824DPJR is the same overvoltage protector family as the rest of the BQ7718 parts, built for two to five cells in series, with the threshold fixed at 3.850 V and a three series configuration. The output is CMOS active high on this option, so a fault drives the pin up rather than pulling it down, and the part needs no pull up resistor to report.

A 3.850 V limit is a deliberate choice for cells that are not charged to the usual 4.2 V. Lithium iron phosphate cells sit near 3.6 V at rest and are charged to 3.65 V, so a 3.85 V limit leaves a sensible margin above the normal charge point while still catching a charger that has lost regulation. The same part is used on packs where the cells are derated on purpose to buy cycle life.

Because the threshold is low, the tolerance matters more in absolute terms. Plus or minus 10 mV on a 3.850 V point is about a quarter of a percent, but it is the same 10 mV that has to absorb the sense wiring error, the temperature drift of the comparator and the mismatch between the cells. A pack built to this point and charged to 3.80 V per cell is running with 50 mV of headroom, which is inside the error budget of a careless sense connection.

Key data for the BQ771824DPJR

FunctionOvervoltage monitor and protector, one comparator per cell
Cell count3 series on this option, 2 to 5 series across the family
Overvoltage threshold3.850 V
Threshold accuracyPlus or minus 10 mV
DelayInternal delay timer, value set by the option
OutputCMOS, active high
Supply currentAbout 1 microamp with all cells below the protection point
Cell input leakageLess than 100 nanoamps per input
Test modeCustomer test mode shortens the delay for production line checks
Package8 pin QFN, 3.00 mm by 4.00 mm
TemperatureMinus 40 to 110 C operating
OrderingBQ771824DPJR, large tape and reel

Choosing the threshold against the charger, not against the cell

A protection point is only meaningful next to the charger that feeds it. If the charger is set to 4.20 V per cell and the protector is at 3.850 V, the protector will trip on every charge and the pack will never fill. The threshold has to sit above the charger regulation point by more than the tolerance of both parts plus the sense error.

With a 3.850 V protector, a charger set to 3.65 V per cell gives 200 mV of room, which is comfortable. A charger set to 3.80 V leaves 50 mV, which is not, unless the sense path is short and the charger is accurate to a few millivolts. The review question is not what the cell can take, it is what the charger will actually deliver at the end of a constant voltage phase on the worst board in the batch.

There is also a temperature dimension. The comparator threshold moves with temperature, and the datasheet accuracy figure is quoted at room. A pack that is charged in a cold store and then carried into a warm room will see the two effects add in one direction. Leaving 100 mV of margin against the charger covers that without turning the protection point into something that never acts.

Why an active high output changes the board

The active high output on this option drives the gate of a charge control device directly, so the usual pull up resistor and its leakage path disappear. On a board that is asleep most of the time, that resistor is not free: a 100 kilo ohm pull up to 3.3 V across an output that is asserted for long periods is 33 microamps, which is more than the whole protector draws.

The other side of the choice is what happens when the protector has no supply. An active high output that is unpowered sits at an undefined level, and a charge FET driven from it can turn on when the pack is flat. Options that use an open drain output invert that problem: the output is pulled down, which is the safe state for a P channel switch, but the pull up has to be present and has to be returned to a rail that exists.

The part has no latch and no host interface. Once the cell falls back below the threshold minus the hysteresis, the output releases by itself, and the charger decides whether to resume. A product that must not resume without a service action needs a latch outside the protector, either in the charger or in the host.

Where it fits in a build

The 3.850 V option turns up in packs built on lithium iron phosphate cells and in packs where the cells are deliberately held below their maximum, which covers medical carts, floor cleaning equipment and stationary backup. In those builds it is usually the last line of defence behind a charger that already regulates properly.

On the supply side, the part is a long life repeat item and the risk is not availability today but the reel that has been in a store for two years. The date code management page covers how we track age, what we will not ship into a new build and what we do with stock that is near the end of its floor life.

The sourcing side of this part is covered on the supplier quality audit. For a part that carries the last layer of protection, that page covers what we check at the source before a reel is accepted.

Questions we get on this code

Can this option be used on a four cell pack? The cell count is set by the option, not by wiring, so a three series part on a four cell pack will not monitor the fourth cell. Use the option that matches the pack, and tie unused inputs to a defined level on options that allow a lower count than the pack.

Does the output drive a relay? No. It is a logic level output meant for a charge control device or a host input. A relay coil needs a driver transistor and a flyback path, and the coil current has to come from somewhere other than the protector.

What is the recovery behaviour if the cell stays high? The output stays asserted. There is no timer that gives up and reconnects, which is the correct behaviour for an overvoltage event, but it means a pack with a failed cell will stay off until someone looks at it.

Is the 3.850 V point available in other packages? The family is offered in an 8 pin QFN and an 8 pin MSOP, and the option code decides the threshold and the output type together. Confirm both when a part number is cross referenced, because a different suffix can change the output polarity as well as the threshold.