BQ771823DPJR
Product Specifications
BQ771823DPJR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ771823DPJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ771823DPJR second level overvoltage protector for two to five cell packs
The BQ771823DPJR watches every cell in a two to five series pack and pulls its output after a fixed delay if any one cell climbs past 4.275 V. It is a second level device: it sits behind the primary protector and exists to open the pack if the primary fails or if a charger keeps pushing current into a cell that is already full. The threshold is fixed in silicon, the delay is fixed at 3 seconds, and there is nothing to program.
The part comes in an 8 pin QFN measuring 3.00 mm by 4.00 mm, with a leaded MSOP option elsewhere in the family. Supply current is about 1 uA while every cell is below the protect threshold, and each cell input leaks less than 100 nA, so a pack that sits on a shelf for a year does not come back flat because of the protector. Accuracy on the threshold is plus or minus 10 mV.
Key parameters taken from the BQ771823DPJR document
| Cells covered | 2, 3, 4 or 5 in series |
| Overvoltage threshold on this order code | 4.275 V fixed, plus or minus 10 mV |
| Overvoltage hysteresis on this order code | 50 mV |
| Output delay on this order code | 3 s fixed |
| Output type on this order code | CMOS active high |
| Supply current | about 1 uA with all cells below the protect threshold |
| Leakage per cell input | below 100 nA |
| Package | DPJ, 8 pin QFN, 3.00 mm by 4.00 mm |
| Operating ambient | minus 40 C to 110 C |
| Test aid | customer test mode with a greatly reduced delay for line testing |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The order code carries the threshold, the hysteresis and the delay, so a BOM that names only the family is not enough. Within the same family the thresholds run from 3.850 V to 4.650 V and the delays run 1 s, 3 s or 4 s depending on the variant. A pack built for a 4.2 V cell with a 4.275 V secondary limit cannot simply take a 4.35 V variant when stock is short, because that moves the second line of defence 75 mV up.
Customer test mode is the feature that production engineers care about. The internal delay drops to a short interval when the test pin is driven, so a pack can be tested on the line in seconds instead of waiting three seconds per unit. Without that mode the test station becomes the bottleneck on a high volume pack line.
The device draws its supply from the pack itself, so the first cell connection order matters during assembly. The vendor specifies tolerance of a random cell attach sequence, but the resistor and capacitor on each cell input still have to be in place before power is applied, otherwise the input sees the full stack through a low impedance.
Because the output is CMOS active high on this variant, it drives a FET or a fuse driver directly and idles low. A pack maker replacing an open drain variant has to check the polarity of the receiving circuit, since the two families look identical on a drawing but behave opposite at the output.
- Threshold accuracy of plus or minus 10 mV is tight enough to sit close to the cell maker's absolute maximum without nuisance trips.
- The 3 second delay filters the voltage spike that appears when a pack FET opens under load, so the protector does not fire on a switching transient.
- Per cell leakage under 100 nA keeps shelf life intact for instruments that are stored for months.
- The 8 pin QFN with no programming pins keeps the pack board small and removes any field reconfiguration risk.
Which projects this part fits
This protector belongs in any pack where a single point failure of the primary protection has to be covered: power tool packs, cordless vacuums, garden tools, e-bike and e-scooter batteries, UPS packs and medical carts. It is also used in packs that ship with a charger whose output can fail high. Our power management cross reference covers the protectors we hold alongside the gauges, and incoming inspection sets out the threshold check we run on each lot.
Variants, output polarity and the first article test list
The family carries its threshold, hysteresis, delay and output type in the order code, and the codes are not interchangeable in a pack. The table below shows the shape of the range, with the values for this order code in the first row.
| Item | Value or option |
| This order code, BQ771823DPJR | 4.275 V, 50 mV hysteresis, 3 s delay, CMOS active high, 8 pin QFN |
| Threshold range across the family | 3.850 V to 4.650 V in fixed steps |
| Delay options | 1 s, 3 s and 4 s depending on the code |
| Hysteresis options | 50 mV or 300 mV depending on the code |
| Output options | CMOS active high, or N-ch open drain active low |
| Package options | DPJ 8 pin QFN, 3.00 mm by 4.00 mm, or DGK 8 pin MSOP |
A substitution inside this family is a safety change, not a purchasing convenience. Moving from a 4.275 V code to a 4.350 V code lifts the second line of defence by 75 mV, which on a 4.2 V cell may be above the point where the cell is already being damaged. Purchasing therefore needs the full order code and the package letter, and a reel that cannot be identified has to be treated as unknown.
One property of this family is easy to overlook when a pack is being costed: the device is supplied from the pack it protects, so it has to survive the pack being assembled one cell at a time. The series resistor and capacitor on each cell tap keep the input current bounded during that sequence, and a board that omits them to save two components is relying on the assembly order rather than on the part.
The first article test is a slow ramp on one cell with the other cells held at nominal, which lets the threshold and the delay be measured separately. Customer test mode shortens the delay, so the test station must either disable it or allow for the shorter interval when the measured delay is compared with the 3 s specification.
Questions that come up before a purchase order is released
Does this part replace the primary protector?
No. It is a second level device with a fixed threshold and a fixed delay, and it has no undervoltage, overcurrent or short circuit function. It is added on top of a primary protector or a gauge that already carries protection, and its job is to act when that primary layer does not.
Why does the delay matter so much?
A three second delay means a short overvoltage spike does not open the pack, while a genuine overcharge condition still opens it long before the cell is damaged. It also means the pack cannot rely on this part for fast events; a short circuit is handled by the primary protector and the FETs, not here.
Can the threshold be changed after the pack is built?
No. The threshold is fixed by the order code. Changing it means changing the part number on the BOM, which is why the variant should be written out in full, including the package letter, rather than left as a family name that a purchaser might fill with the nearest available reel.
How SUPERB handles this line
We stock the BQ771823DPJR and the neighbouring threshold variants as separate line items, and every reel is checked against the ordered threshold before it goes into a kit. If a pack line is short of one variant, we will say which variant is available rather than substitute silently, because the threshold is a safety number. Use the date code management page for the shelf life rules we apply to protectors held in stock.