BQ7695202PFBR
Product Specifications
BQ7695202PFBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ7695202PFBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ7695202PFBR: 3S to 16S battery monitor and protector with high side NFET drive and dual LDOs
BQ7695202PFBR is a battery monitor and protector for lithium packs in a TQFP body of 48 pins. The part measures cell voltages, pack current and up to nine external thermistors, drives high side N-channel protection FETs from an internal charge pump, and runs autonomous or host controlled cell balancing, all in a 7 mm by 7 mm body that tolerates 85 V on the cell connections.
Order code and package
| Order code | BQ7695202PFBR |
| Package | TQFP, 48 pins, 7.00 mm by 7.00 mm |
| Cells | 3 series to 16 series |
| Cell connection rating | 85 V |
| Current sense range | plus or minus 200 mV across the shunt |
| Interfaces | 400 kHz I2C, SPI, HDQ one wire |
| Auxiliary rails | two programmable LDOs |
| Configuration memory | customer programmable OTP |
| Temperature range | minus 40 to plus 85 degrees Celsius |
Electrical parameters that decide the application
| Cell voltage accuracy | better than 10 mV typical |
| Coulomb counter offset | better than 1 microvolt typical |
| Normal mode current | 286 microamp |
| Sleep mode current | 24 to 41 microamp |
| Deep sleep current | 9 to 10 microamp |
| Shutdown current | 1 microamp |
| Thermistors | internal sensor plus up to nine external |
| Balancing | autonomous or host controlled |
Points to check before this part goes on a BOM
286 microamps in normal mode is 2.51 Ah over a year, so a 20 Ah e-bike pack loses 12.5 percent of its charge to the monitor alone if it is never put on a charger. The deep sleep options at 9 to 10 microamps cut that to about 79 mAh a year, which is why the mode policy matters as much as the cell chemistry for a pack that ships and stores.
Shutdown at 1 microamp is 8.8 mAh over a year, but the part cannot protect the pack in that state, so a product that ships in shutdown relies on the cells and the fuse instead. The difference between 286 microamps and 1 microamp over a year is 2.5 Ah, which is a visible fraction of a small pack.
The current sense range is plus or minus 200 mV. A 100 A peak pack needs a 2 milliohm shunt to use the full range, a 200 A pack needs 1 milliohm, and at 1 milliohm and 100 A the signal is 100 mV, so half of the converter range is never used and the resolution is halved with it. The shunt value is the decision that fixes both the measurement resolution and the heat in the shunt.
A coulomb counter offset better than 1 microvolt is 1 mA through a 1 milliohm shunt, and 1 mA for 8760 hours integrates to 8.76 Ah of phantom charge over a year. That is why the offset figure and an occasional full cycle matter more than the coulomb counter resolution: without a re-zero the state of charge drifts faster than the cell self discharge.
Cell voltage accuracy better than 10 mV is stated as typical. An over voltage threshold set at 4.25 V for a 4.20 V cell therefore carries the measurement error on top of the threshold tolerance, and on a LiFePO4 pack the plateau is so flat that 10 mV covers a wide band of state of charge, so the guard band has to come from the configured threshold rather than from the measurement.
The 85 V rating on the cell connections is what allows a 16S pack to be assembled or serviced with the cells attached in random order on a production line. A 16S Li-ion string sits at 67.2 V and a 16S LiFePO4 string at 58.4 V, so the headroom is there for the attach sequence and not for a charger fault.
This order code is rated minus 40 to plus 85 degrees Celsius, not the 125 degrees the die can take. A pack that sits next to a motor or in a sealed enclosure has to keep the board under 85, and the thermal path from the 7 mm body is part of that calculation rather than an afterthought.
The base part defaults to I2C, while other members of the family ship with a different default; the BQ7695201 for example comes up in SPI with CRC enabled. Because the interface, the CRC setting and the LDO defaults all come out of OTP, the order code suffix has to match the production fixture and the host firmware, and a substitution across suffixes is a firmware change.
Two independent converters sample current and cell voltage at the same time, so a short circuit is caught in the same window as the voltage collapse that follows it. Parts that multiplex one converter across sixteen cells cannot make that comparison, and the difference shows up in how fast the protection reacts to a hard short rather than in any steady state accuracy figure.
The two LDOs are programmable and one of them is disabled by default on the base part. A pack that expects 3.3 V for its host from REG1 has to program it first, and a substituted suffix with a different default comes up with that rail off, which looks like a dead host rather than a wrong order code.
Balancing current is set by the external resistors and the cell voltage, not by the part. At 3.6 V a 100 ohm resistor gives 36 mA per cell, which on a 50 Ah pack is a rounding error and on a 5 Ah pack is a useful current. The resistor value is therefore a pack decision that has to be revisited whenever the cell capacity changes.
Where this order code fits
Battery backup units, e-bikes, e-scooters, cordless power tools, garden equipment and industrial 10S packs are the applications this monitor and protector is specified into. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Does the part balance the cells itself? It supports autonomous balancing as well as host controlled balancing. In autonomous mode the thresholds come from OTP or registers, so the pack can balance without the host being awake, which is what keeps a stored pack in step.
Can it drive the protection FETs directly? Yes. The internal charge pump drives high side N-channel FETs, including the precharge and discharge paths, and there is a separate drive for a secondary chemical fuse for the case where the FETs fail short.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.