BQ7694204PFBR
Product Specifications
BQ7694204PFBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ7694204PFBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ7694204PFBR: a 3S to 10S protector with high side drive
The BQ7694204PFBR is a battery monitor and protector for packs of three to ten series cells. It carries two independent converters, a charge pump for high side FET drive, dual programmable regulators and a chemical fuse drive, all in a 48 pin TQFP. The part reads cells and current at the same time, applies a configurable protection set, and balances the cells either on its own or under host control.
High side drive is the difference between this family and the low side front ends. The charge and discharge FETs sit in the pack positive path, so the pack negative stays a solid ground for the tool, the charger and the host. On a product where the pack is inserted into a device that shares its ground with other systems, that removes a whole class of ground offset faults.
Current is measured across an external sense resistor with a plus or minus 200 mV range, and the coulomb counter offset is quoted below 1 microvolt typical. Cell accuracy is quoted below 10 mV typical. The part reports over I2C, SPI or the single wire HDQ format, and the 200 microamp class consumption figures mean a pack can sit for months without a charge.
Key data for the BQ7694204PFBR
| Function | Battery monitor and protector with high side FET drive |
| Cell count | 3 to 10 series cells, Li-ion, lithium polymer and LiFePO4 |
| Converters | Two independent converters, simultaneous current and voltage sampling |
| Current accuracy | Coulomb counter input offset below 1 microvolt typical |
| Cell accuracy | Cell voltage measurement below 10 mV typical |
| Current range | Plus or minus 200 mV across the sense resistor |
| FET drive | Charge pump driving high side N channel charge and discharge FETs, autonomous recovery option |
| Protection | Voltage, temperature, current, short circuit, plus a secondary chemical fuse drive |
| Regulators | Two programmable LDO outputs for external system use |
| Interface | 400 kHz I2C, SPI, or HDQ single wire, selected by the variant |
| Package | TQFP, 48 pins |
| Ordering | BQ7694204PFBR, 1000 pieces on a large tape and reel, moisture level 2 with a one year floor life |
The variant suffix sets the interface, and the board has to match
The family ships several members that share a die and a package, and the suffix sets the default host interface and the CRC setting. The family table lists an I2C row and two SPI rows, and the fourth member ships with its own default. A host driver written for one row will not talk to another without a configuration change.
This matters most at the prototype stage, where a board is laid out with the pins shared between the interfaces and the host code assumption is made early. A board that expects I2C and receives an SPI default looks dead on the bench, and the usual hour is lost looking at the pull ups before anyone reads the variant table.
The safest approach is to fix the suffix before the board is frozen, and to write the interface into the build documentation rather than into someone's memory. A part that is second sourced later has to match both the interface and the CRC setting, not just the package.
High side drive, in a pack that shares its ground
In a low side arrangement the FETs sit between the cell stack negative and the pack negative terminal, so the pack negative moves by the FET drop under load. A tool that references its own electronics to the pack negative sees that movement as a supply change, and a charger that references its output to the same node sees it too. On a small pack the drop is tens of millivolts and nobody notices; on a 40 A tool it is enough to upset a comparator.
Moving the FETs to the positive side removes that. The pack negative is then the cell stack negative, and everything downstream sees a stable reference. The cost is the charge pump, because the gate of a high side N channel FET has to be driven above the pack voltage, and the pump has to hold that up while the FET is on.
The pump is also a load. It switches continuously while the FETs are on, and its current is part of the pack quiescent draw. On a product that leaves the FETs on for months, that current has to be in the standby budget next to the gauge and the host.
Where it fits in a build
Packs from three to ten cells where the ground reference matters and the protection has to be independent of the host: power tools, garden equipment, vacuum cleaners, light electric vehicles, non military drones and industrial battery packs. A pack that needs more than ten cells moves to the 16 cell member of the same family in the same package.
Because this part carries the protection as well as the measurement, a change of cell vendor lands on the configuration rather than on the board. For a programme facing that change, the component obsolescence management page covers the alternates we qualify before a row changes.
The sourcing side of this part is covered on the BOM shortage recovery. For a build that has to keep a protection part on the line, that page covers what happens when the reel runs short.
Questions we get on this code
Does it balance without the host? Yes, autonomous balancing is a configuration option, and the host can take control when a specific policy is needed. The autonomous mode pauses on temperature and resumes when the pack cools.
What are the two regulators for? They supply external loads such as the host or a radio from the pack, at voltages that are set in configuration. They are not system rails and their current is limited.
Why does the coulomb counter offset matter so much? A small offset integrated over weeks becomes a large charge error. Below 1 microvolt typical on a 1 milliohm resistor is a nanoamp class offset, which is what keeps a long integration honest.
Can the same board build an 8S and a 10S pack? Yes, the cell count is a configuration item, and the unused sense inputs are tied off. The thresholds and the balancing settings change with the count.