BQ50002ARHBT
Product Specifications
BQ50002ARHBT
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ50002ARHBT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ50002ARHBT five volt wireless power transmitter front end for WPC low power transmitters
The BQ50002ARHBT is the analog half of a two chip wireless power transmitter. It contains the MOSFET drivers, the synchronous power FETs, the current sense, the variable frequency oscillator, the regulator and the demodulator that decodes the control packets coming back from the receiver. The digital half is a separate controller, the bq500511A, and the pair is intended for 5 V input transmitters that deliver 5 W at the receiver output under the Wireless Power Consortium low power specification, revision 1.2 A11.
The reason to look at an analog front end rather than a single chip is efficiency and thermal spread. The power stage is outside the controller, so the heat from the FETs does not sit under the same body, and the vendor quotes transmitter efficiency above 75 percent from the pair. Standby draw is stated as below 30 mW even during a digital ping, which is the number that decides whether a product can leave its transmitter energised all day.
Key parameters taken from the BQ50002ARHBT document
| Function | wireless power transmitter analog front end, to be paired with the bq500511A controller |
| Standard | WPC low power transmitter specification v1.2 A11, 5 V input |
| Receiver output | 5 W |
| Integrated power stage | MOSFET drivers and synchronous N channel power FETs |
| Integrated analog | current sense, variable frequency oscillator, regulator, high sensitivity demodulator |
| Efficiency | above 75 percent for the two chip transmitter |
| Standby | below 30 mW including the digital ping interval |
| Protection and control | dynamic power limiting from a limited input source, foreign object detection, LED state and fault indication |
| Package | VQFN RHB, 32 pins |
| Order code facts | BQ50002ARHBT, 250 pieces on a small reel, MSL Level-1-260C-UNLIM, minus 40 to plus 125 C, marking Q50002A |
| Lifecycle | the addendum status column reads NRND for every row of this code |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The lifecycle status is the first thing a buyer should see. Every row of this code in the vendor addendum is marked NRND, which means the vendor no longer recommends it for a new build. That does not make the part unusable, and it is still listed as in production, but a product that expects a five year supply should be planned with a last time buy or a qualified alternate rather than with an assumption of continued availability. For an existing product that is already certified, staying on the part and holding a buffer is usually cheaper than a re qualification.
The controller pairing has one trap that the vendor states plainly. The bq50002A is not compatible with the earlier bq500511 controller when foreign object detection is required, so the pair has to be the A version on both sides of the interface. A bill of materials that mixes the older controller with this front end will power a receiver and will still charge a phone, which is exactly why the fault can survive a bench test and appear only in a certification review.
Foreign object detection is not a software feature that can be added later. It depends on the power loss measurement, which depends on the accuracy of the current sense inside this device and on the calibration done by the controller. The vendor describes an accurate method, and the practical consequence is that the sense resistor and its Kelvin connection are part of the safety chain, not just part of the loop. A board that runs the sense traces under the switching node will produce a loss estimate that drifts with temperature.
Dynamic power limiting is the feature that lets a transmitter run from a 5 V source that cannot supply the full peak, such as a USB port or a small adapter. When the input sags, the transmitter reduces its output instead of collapsing the rail, so the receiver sees a slower charge rather than a restart. For a product that shares one adapter between a transmitter and another load, this behaviour is what keeps the second load alive.
Thermal behaviour follows the copper. The 32 pin body has an exposed pad, and the FETs inside it dissipate during a full 5 W transfer. The vendor board uses a large copper area on both layers with vias under the pad. A transmitter built into a small plastic shell without that copper will fold back or shut down after a few minutes, and the failure will look like a coil problem rather than a thermal one.
- The 250 piece small reel is the only published packing for this code, so a prototype build and a production build order the same reel size.
- Moisture level 1 with unlimited floor life is unusual for a power part and it simplifies handling on a line that opens and closes reels often.
- The demodulator sensitivity decides how much margin the coil alignment has, so the sense network around it should follow the vendor values rather than a scaled copy.
- Two chip transmitters spread the heat, but they also add one more interface to verify in test, so the production fixture needs a way to read the controller state.
- The marking Q50002A is the quickest way to separate this front end from the earlier non A version on an incoming bench.
- The coil and the resonant capacitor values come from the controller vendor's reference coil set, and a transmitter built around a different coil needs the loss model recalculated before the foreign object threshold is set.
Which projects this part fits
Wireless charging transmitters for phones, earbud cases, wearables, medical handhelds that must be sealed, and proprietary chargers built around a 5 V input all fit this two chip approach. Buyers look at it when a single chip transmitter cannot hold efficiency or when the thermal budget in a closed enclosure is tight. It is also the cheaper route for a product that only needs 5 W and does not want to carry the cost of a higher power controller. Our power management cross reference lists alternates we can hold against this family, and the obsolete part cross reference hub is where a replacement search starts once a line is marked NRND.
Questions that come up before a purchase order is released
Is this part still available for a new build?
The vendor marks it NRND, not recommended for new builds, and it remains in production. A new product should treat it as a bridge part: qualify it, hold a buffer, and plan the alternate before the volume ramp rather than after the last time buy window closes.
Can it be used with the older controller to save cost?
Only if foreign object detection is not required. The vendor states the A front end is incompatible with the non A controller when that function is needed. Mixing the two will still transfer power, so the mistake is not caught by a simple bench test.
What decides the real output power?
The coil pair, the resonant capacitors and the input source together. The front end supports 5 W at the receiver output with the vendor coil set, and a smaller coil or a weak adapter will limit the result before the silicon does.
How SUPERB handles this line
We supply the BQ50002ARHBT on its 250 piece small reel with date code and lot traceability, and we flag the NRND status on the quote so that the planning decision is made openly. If the product is already certified and the only question is continuity, send the annual volume and we will hold a buffer against it. If the product is new, start from the obsolete part cross reference hub and we will check what is available before the netlist is frozen. That check covers the controller pairing, the coil set and the input source.