BQ34Z100PWR-G1
Product Specifications
BQ34Z100PWR-G1
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ34Z100PWR-G1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ34Z100PWR-G1: one gauge across a 3 V to 65 V pack
The BQ34Z100PWR-G1 is a pack side fuel gauge that works from a single cell up to a stack that sits at 65 V. The cell count is set by an external divider rather than by the part, so one order code covers a 12 V battery, a 24 V battery and a 48 V battery, and the same host code reads all three. That is the reason this part shows up on industrial bills of material where several pack voltages ship from one production line.
Inside, the gauge runs Impedance Track modelling, which follows the change in cell impedance as the pack ages and uses it to hold state of charge accuracy as capacity falls away. The vendor quotes around 1 per cent error for the state of charge figure across the operating range, which is a claim about the algorithm on a correctly configured pack rather than a property that survives a wrong chemistry profile.
The part talks I2C or the single wire HDQ format, and it drives one or four LEDs directly for a state of charge display, or more through a port expander. Current is measured across an external sense resistor, and the supported range with the standard configuration options reaches 32 A.
Key data for the BQ34Z100PWR-G1
| Function | Pack side fuel gauge with Impedance Track modelling |
| Pack voltage | 3 V to 65 V, cell count set by an external divider |
| Current range | Up to 32 A with the standard configuration options |
| Interface | I2C slave or HDQ single wire, plus an alert output |
| Display | One or four LEDs driven directly, more through a port expander |
| Normal current | Under 145 microamps average |
| Sleep current | Under 84 microamps average, under 30 microamps in full sleep |
| Temperature input | External thermistor on the pack, internal sensor as a fallback |
| Data memory | Configuration and learned values held in the part, no host side model |
| Package | TSSOP, 14 pins, 5.00 mm by 4.40 mm |
| Temperature | Minus 40 to 85 C operating |
| Ordering | BQ34Z100PWR-G1, 2000 pieces on a large tape and reel, moisture level 2 with a one year floor life |
The divider is the part that decides whether it works
Because the pack voltage arrives through a resistor divider, the accuracy of that divider becomes the accuracy of every voltage reading the gauge makes. The vendor asks for 0.1 per cent resistors with a 25 ppm temperature coefficient, and that is not a suggestion to be traded away for a cheaper part. A 1 per cent divider adds a 1 per cent error to the cell voltage the model uses, and the model will then misplace the top of the charge curve by a visible margin.
The divider also draws current continuously unless the part switches it off, and the part has a control for that. Left on, the divider can cost tens of microamps, which on a pack that sits on a shelf for a year is a measurable loss. Tie the divider to the control pin and let the gauge enable it when it takes a reading.
The scaling from pack voltage to the input range is set in the data memory, and it has to match the resistors actually fitted. A build that changes the divider for a different pack voltage and leaves the scale factor alone will read a plausible but wrong voltage, and the state of charge will follow it.
Where the model needs help from the pack
Impedance Track learns, and what it learns from is the pair of a rested voltage reading and the current that follows. A pack that is never allowed to rest, or that is charged and discharged in a narrow band around half charge, gives the model little to work with and the initial accuracy holds rather than improving. A pack that is cycled to a low state of charge now and then keeps the model honest.
Temperature is the second input. The thermistor has to be on the cells, not on the board, because the model needs the cell temperature to predict impedance. A thermistor next to a warm regulator reads high, and the model will understate the available capacity in cold conditions and overstate it in a hot cabinet.
The learned values live inside the part. If the part is replaced on a service board, the model starts again from the stored configuration and the pack looks new for a few cycles. That is a service procedure to write down rather than a failure of the part.
Where it fits in a build
This is the gauge for a pack with a display, a defined charge and discharge pattern, and enough volume that the host board is shared across several pack voltages. Light electric vehicles, floor care, energy storage cabinets, industrial power tools and medical carts all fit that description. A product with a single cell and no display is better served by a smaller system side gauge.
Packs at these voltages are also where a change of cell vendor lands hardest, because the model has to be reloaded when the cell changes. On a programme that needs a second cell source, the obsolete part cross reference hub sets out how we compare alternates and what evidence we ask for before calling one equivalent.
The sourcing side of this part is covered on the supplier quality audit. For a gauge that carries the pack model, that page covers what we check at the supplier before a reel is accepted.
Questions we get on this code
Can one configuration cover several pack voltages? The part is configured for a given divider ratio, and the pack voltage scale is a data memory value. A production line that builds more than one voltage either loads a different configuration per variant or fits a divider that keeps the same ratio across the range.
Does the gauge work without a host processor? It can drive one or four LEDs by itself, so a simple pack with a state of charge light needs no host at all. Anything more detailed needs a host to read the registers over I2C or HDQ.
What happens when the pack is deeply discharged and the gauge loses power? The configuration survives in data memory, and the learned values are recovered as the pack cycles. The state of charge will be approximate for the first cycle after a full loss of supply, which is worth knowing before a low battery warning is trusted again.
Is the 32 A figure the maximum the pack can deliver? No, it is the current range the standard configuration is set up to measure across the sense resistor. Higher currents need a different resistor value and a matching scale, and the limit then belongs to the resistor and the copper rather than to the gauge.