BQ29728DSER
Product Specifications
BQ29728DSER
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ29728DSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ29728DSER: a single cell protector tuned for pulsed loads
The BQ29728DSER is a single cell protector in the same 6 pin family as the rest of the BQ297xx line, with a set of thresholds chosen for products that draw current in bursts rather than steadily. The overdischarge delay is 144 milliseconds and the discharge overcurrent trip is 150 mV, both longer and higher than the fast trip members. A module that transmits for 200 milliseconds at a time will ride through its own transmit burst on this part, and would trip on a tighter one.
The other thresholds are 4.280 V overcharge with a 1.25 second delay, 2.800 V overdischarge, minus 100 mV charge overcurrent with an 8 millisecond delay and a 0.6 V short circuit trip with a 250 microsecond delay. The short circuit response stays fast because that event is not a normal load, and the pack has to disconnect before the FETs are damaged.
The body is a 6 pin WSON at 1.75 mm by 1.75 mm, the part is rated minus 40 to 85 C and the finish is nickel palladium gold. Marking is EJ on both printed rows.
Key data for the BQ29728DSER
| Function | Single cell voltage and current protection with FET drive |
| Overcharge | 4.280 V, 1.25 second delay |
| Overdischarge | 2.800 V, 144 millisecond delay |
| Charge overcurrent | Minus 100 mV across the FETs, 8 millisecond delay |
| Discharge overcurrent | 150 mV across the FETs, 8 millisecond delay |
| Load short circuit | 0.6 V, 250 microsecond delay |
| Current accuracy | Plus or minus 5 mV typical on the overcurrent sense |
| Pack input range | Minus 0.3 V to 12 V |
| FET drive | Separate charge and discharge drive outputs |
| Package | WSON, 6 pins, DSE body, 1.75 mm by 1.75 mm |
| Temperature | Minus 40 to 85 C |
| Ordering | 250 pieces on a small tape and reel on both printed rows, marking EJ |
Why a longer overdischarge delay changes the cell choice
A 144 millisecond overdischarge delay means the pack can sit below its undervoltage threshold for that long without disconnecting. On a pulsed load that is exactly what is wanted: the cell voltage sags during the burst, recovers between bursts, and the pack keeps delivering. On a steady load the delay does nothing, because a pack that is genuinely flat stays below the threshold.
The cost is that the cell is allowed to sit below its minimum for a little longer on every burst at the end of discharge. Cell vendors specify the minimum voltage at the cell terminals under load, and a delayed trip means the average voltage during the burst is lower than the threshold. If the pack is being run to the last few per cent regularly, the delay is shortening the cell life. If it is being run to 20 per cent and recharged, the delay is invisible.
The counterpart is the higher discharge overcurrent trip at 150 mV. Combined with a pair of FETs at 20 milliohms, that is 7.5 A before the pack disconnects, which is enough for a transmit burst or a motor start on a small tool and not enough to protect a 1 A cell from a dead short on the load side. The short circuit detector covers that case separately at 0.6 V and 250 microseconds.
Reading the reel rows before a build
Both printed rows of BQ29728DSER show 250 pieces on a small tape and reel. There is no 3000 piece large reel row in the addendum for this string, which is unusual for the family and worth knowing before a production order is placed. A build that needs 30,000 pieces will be taking 120 small reels, and the line has to be set up for that carrier.
The 250 piece reel is also the right unit for a pilot. It is enough for a few hundred boards with attrition, and it does not leave a large reel ageing on a shelf if the programme changes direction.
Where it fits in a build
This is the row for a single cell product with a burst load: a cellular module that transmits, a handheld with a motor, a portable instrument with a heater pulse. The higher discharge trip and the longer undervoltage delay are the two numbers to check against the load profile, and both are visible in the comparison table without opening the electrical section.
When a running product needs this string replaced by an equivalent, the how to verify a drop in replacement page sets out the checks we run before a substitute is offered as equivalent.
The sourcing side of this part is covered on the supplier quality audit. For a protector whose thresholds set the pack current limit, that page covers the checks we run before a substitute is called equivalent.
Questions we get on this code
Is 150 mV the discharge current limit? It is the sense voltage. The current follows from the on resistance of the two FETs, so the pack specification has to name the FETs as well as the protector.
Can the part be used on a 2 series pack? No. It monitors one cell and drives one pair of FETs. A 2 series pack needs two of these or a pack level protector.
What happens if the load is removed during an overcurrent event? The part releases after the delay and the pack recovers, provided the fault has cleared. A latched version of the same function exists in other members of the family, and the choice is a pack policy decision.
Does the marking EJ tell us the reel size? No, both rows print EJ. The reel size is on the label and on the purchase order, which is why the carrier has to be named when ordering.