Contact Us

BQ294700DSGR

Brand: Texas Instruments
Texas Instruments BQ294700DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ294700DSGR — Power Management & Signal Chain | Superb Automation

BQ294700DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ294700DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ294700DSGR: a second level trip whose delay is set by a capacitor

The BQ294700DSGR is an overvoltage protector for two, three or four cells in series, and the difference from the fixed delay members is the CD pin. Instead of a delay burned into the silicon, an external capacitor sets it, and the part also watches that pin for an open or shorted capacitor and drives its output if the timing element has failed. That last feature is the reason to choose this part on a pack where the second level has to be provably alive.

The trip point on this code is 4.350 V with a 1 kOhm series resistor in the sense path, the accuracy is plus or minus 10 mV, supply current is about 1 microamp and the leakage on each cell input is under 100 nA. The output is a CMOS active high drive, and the body is an 8 pin WSON at 2 mm by 2 mm.

The delay equation in the document is t equal to K times the capacitor value, with K between 10 and 20. A 0.1 microfarad capacitor therefore gives somewhere between 1 second and 2 seconds, and the capacitor tolerance widens that window further. A 1 microfarad part gives 10 to 20 seconds.

Key data for the BQ294700DSGR

FunctionOvervoltage protection for 2, 3 or 4 series cells, secondary level
Overvoltage threshold4.350 V fixed, read with a 1 kOhm input resistor
Threshold accuracyPlus or minus 10 mV
DelaySet by the capacitor on the CD pin, 10 to 20 seconds per microfarad
Timer supervisionOpen or shorted CD capacitor still drives the output active
Supply currentAbout 1 microamp with all cells below the trip point
Cell input leakageUnder 100 nA per input
OutputCMOS active high, or open drain active low, per the option
PackageWSON, 8 pins, 2 mm by 2 mm
TemperatureMinus 40 to 110 C on the DSGR row
Ordering3000 pieces on a large tape and reel, moisture level 1 at 260 C, marking 700
Test modeCustomer test mode with a shortened delay for line testing

The timer that checks its own capacitor

An external timing capacitor is a component that can fail. It can crack, it can be missing after a rework, and it can short. On a delay circuit built from a comparator and a capacitor, any of those faults leaves the output either permanently active or permanently inactive, and a permanently inactive second level is indistinguishable from a healthy one until the day it is needed.

This part closes that hole. The CD pin is charged when a cell crosses the trip point and then discharged at a fixed current, and the output goes active when the pin falls below a threshold near the negative rail. The same pin is monitored for a value outside the expected window, and a fault there drives the output active in its own right. The behaviour is a deliberate trade: a failed capacitor trips the fuse rather than leaving the pack unprotected. A service technician will see a pack that trips with a good capacitor missing, which is the correct outcome.

Choosing the capacitor is therefore a decision about how long a real overvoltage is allowed to persist. A 0.1 microfarad part gives 1 to 2 seconds, which is quick enough to protect a cell and slow enough to ignore a transient. A 1 microfarad part gives 10 to 20 seconds, which suits a pack where the primary protection has its own delay and the second level only has to catch a failed primary.

Temperature range and the two rows that look the same

The DSGR row is rated minus 40 to 110 C. The G4 row of the same body is rated minus 40 to 85 C, and the two carry the same marking, so a reel label is the only way to know which grade is inside. On a pack that runs hot, the 110 C part is the one to specify, and the difference is not visible on the board.

The DSGT row is the 250 piece small reel, and there is a second row under the same string that lists 3000 pieces with a different marking. That is a document artefact rather than two parts, and the safest route is to name the carrier and the quantity on the purchase order and let the distributor quote the row it holds.

Where it fits in a build

Notebook packs, UPS battery strings and medical packs with 2 to 4 series cells are the applications. The 110 C rating makes it usable next to a power stage that runs warm, and the CD pin makes it usable in a pack where the second level delay has to be justified in a safety file.

When a pack built around this part is being kept alive past the point where the vendor would prefer it, the component obsolescence management page covers the last time buy and the alternate we would qualify.

The sourcing side of this part is covered on the last time buy and LTB planning. For a pack that is expected to run for a decade, that page covers how the buy is sized against the remaining build plan.

Questions we get on this code

What capacitor should be used on CD? A low leakage ceramic with a stable dielectric. The timing current is small, so a leaky capacitor changes the delay by more than its tolerance suggests, and the fault detector may read it as a shorted part.

Does the part latch after a trip? It releases when every cell falls below the trip point minus the hysteresis. In a fuse arrangement the fuse is open by then, so the release only matters for a switched arrangement.

Can the output drive a relay? It is a CMOS output with a small drive current, so a relay needs a transistor between the two. The output is meant for a fuse driver or a logic input.

Why is the threshold specified with a 1 kOhm resistor? The resistor is part of the input network and the threshold is trimmed with it in place. Changing that value moves the effective trip point, so keep the value the document shows unless the change is qualified.