Contact Us

BQ294512DRVR

Brand: Texas Instruments
Texas Instruments BQ294512DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ294512DRVR — Power Management & Signal Chain | Superb Automation

BQ294512DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ294512DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ294512DRVR: second level overvoltage protection for a 2 or 3 series pack

The BQ294512DRVR is a secondary overvoltage protector. It sits above the primary protector in a pack and watches each cell independently, and when any cell crosses its fixed threshold for longer than the fixed delay, it drives its output high. That output is used to blow a fuse, or to turn off a charge FET that the primary protection has already failed to open. It is the part that makes a pack fail safe rather than fail closed.

The threshold on this code is 4.4 V and the delay is 4 seconds. Both are fixed in the silicon, which is the point of secondary protection: there is nothing to program, nothing to misconfigure, and nothing that a bus fault can reset. Accuracy is plus or minus 10 mV over the operating range, and supply current is about 1 microamp, so a pack can sit on a shelf for years with the second level armed.

The body is a 6 pin WSON in the DRV package. Each cell has its own sense input, and the output is active high, which suits a fuse driver or an external switch rather than a direct FET gate.

Key data for the BQ294512DRVR

FunctionSecondary overvoltage protection, one input per cell
Cell count2 series or 3 series
Overvoltage threshold4.4 V fixed in the silicon
Threshold accuracyPlus or minus 10 mV
Delay4 seconds fixed
OutputActive high, triggered after the delay expires
Supply currentAbout 1 microamp
PackageWSON, 6 pins, DRV body
TemperatureMinus 40 to 85 C
Ordering3000 pieces on a large tape and reel, 250 on a small reel, marking 4512
Moisture levelLevel 2 at 260 C, one year floor life

Why a second level exists at all

A primary protector can fail. It can fail open, in which case the pack keeps charging with no protection, or it can fail with its charge FET stuck on, which is the same outcome from the cell point of view. The secondary device is there for that case. It is a separate die, often on a separate supply tap, with its own threshold above the primary one, and its job is to be the last thing that acts.

The 4 second delay is not a slow number by accident. A secondary protector that trips on a transient protects nothing and creates field failures. Four seconds of sustained overvoltage on a cell means the primary has not acted, and at that point the pack is in a condition where a blown fuse is the right answer.

The 4.4 V threshold pairs with a primary threshold around 4.25 V to 4.3 V on a 4.2 V cell. That leaves a margin wide enough that a normal charge with a little overshoot does not reach it, and narrow enough that a runaway condition reaches it before the cell is damaged.

Level 2 moisture and what it means on a 6 pin body

This is a moisture level 2 part with a one year floor life, not an unlimited one. A 6 pin WSON has a small body and a large pad area relative to its volume, and the package takes on moisture faster than a leaded part of the same footprint. The practical rule is to keep the reels sealed until the line is ready, and to bake according to the label rather than according to a general rule for small packages.

The finishing is nickel palladium gold with tin, which matters on a pack that will be potted or conformally coated. A tin finish under a coating that is not fully cured can grow whiskers, and a whisker in a pack protection circuit is a short across a cell sense input.

Where it fits in a build

Two and three cell packs in notebooks, power tools, medical devices and portable instruments are the applications this part was written for. On a 4 series pack it does not fit, and the 4 series member of the same family does. On a single cell pack it is unnecessary, because a single cell has no series string to unbalance.

For a medical pack where the secondary protection is part of the risk file, the medical device components page covers the traceability and incoming inspection records those builds carry.

The sourcing side of this part is covered on the date code management. For a level 2 part with a one year floor life, that page covers how the label date is tracked from reel to build.

Questions we get on this code

Can the output drive a FET gate directly? It is an active high logic output, not a gate driver. A small logic level FET can be switched from it, and a power FET needs a driver stage between the two. Treating the output as a gate drive is the most common mistake on this family.

Is the 4.4 V threshold available in other values? The family covers 3.85 V to 4.6 V in fixed steps, with 4 second and 6.5 second delay options. The code decides both, so choosing a different threshold means choosing a different orderable part.

Does it need its own supply filter? The sense inputs sit across cells with long traces in some packs, and a small series resistor with a capacitor at the pin is the usual arrangement. The part draws about a microamp, so the filter can be a high value without dropping the supply.

What if a cell input is left floating on a 2 series build? The third input must be tied to the top of the stack, not left open. A floating sense input on this family reads as an overvoltage, which blows the fuse at first power up and looks like a failed part.