Contact Us

BQ29312PWR

Brand: Texas Instruments
Texas Instruments BQ29312PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ29312PWR — Power Management & Signal Chain | Superb Automation

BQ29312PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ29312PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ29312PWR: the analogue front end that sits between the cells and the gauge

The BQ29312 is a pack protection front end for two, three or four Li-ion or Li-polymer cells in series. It is not a gauge. It measures each cell, drives the charge and discharge FETs, runs the cell balancing switches, and hands the cell voltages to a host over I2C so a gauge such as the bq2084 family can decide what to do with them. On a notebook pack or a medical battery, this is the part that stands between the cells and the outside world.

The die carries a 3.3 V, 25 mA low dropout regulator, which is enough to run the front end and a small host without a second supply. The supply range is 4.5 V to 25 V, so the same part covers a 2 series stack at the bottom and a 4 series stack at the top. Typical supply current is 60 microamps.

Protection is autonomous in the sense that matters. On an overcurrent or short circuit condition the part turns the FET drive off according to its internal configuration, without waiting for the host to notice. The host can read what happened afterwards, but the disconnect does not depend on a bus transaction completing.

Key data for the BQ29312PWR

FunctionPack protection analogue front end for 2, 3 or 4 series Li-ion cells
Supply range4.5 V to 25 V
Supply current60 microamps typical
Regulator3.3 V, 25 mA low dropout, on the die
Cell measurementIndividual cell voltages and pack voltage reported to the host
BalancingIntegrated cell balancing drive
FET controlCharge, discharge and pre charge drive outputs
InterfaceI2C compatible, built to pair with the bq2084 gauge family
Fault responseAutonomous FET turn off on overcurrent and short circuit per internal configuration
PackageTSSOP, 24 pins
TemperatureMinus 25 to 85 C
Ordering2000 pieces on a large tape and reel, moisture level 1 at 260 C, marking 29312PW

Where the front end stops and the gauge starts

The front end measures and switches. The gauge decides. That split is why the part reports cell voltages to the host rather than acting on a state of charge estimate of its own, and why the internal protection thresholds are about safety rather than about user experience. A pack built with this part alone protects the cells and tells the host what it sees. A pack built with this part and a gauge also reports remaining capacity, and the two communicate over the same bus.

The practical consequence is that replacing the gauge in a running pack does not require replacing the front end, and the reverse is also true, provided the bus stays the same. When a programme changes the gauge to a newer member with a different register map, the front end stays put and the host code that reads it has to change. That is a smaller job than a new pack.

The 25 milliamp regulator and what it can carry

The internal regulator is the reason this part can run a pack with no separate housekeeping supply. 25 mA at 3.3 V is enough for the front end, a small gauge and a thermistor network, and not enough for anything that transmits. On a pack that also carries a wireless reporting module, the module needs its own rail, and the front end regulator should not be assumed to feed it.

The regulator also sets the gate drive headroom. The FET drive outputs are referenced to the pack, and the available gate voltage depends on the regulator holding up at the top of the stack. At 25 V in, the regulator is dissipating the difference between the pack and 3.3 V at whatever current the load draws, so a 20 mA load at 24 V input is about 0.4 W inside the package. The thermal path on a 24 pin TSSOP is not generous, and the copper under the part is doing the work.

Where it fits in a build

Notebook packs, medical battery packs, test equipment and portable instruments with a 2 to 4 series stack are the natural home. The 25 V ceiling means a 4 series stack at 4.2 V per cell, 16.8 V nominal, has margin, and a 6 series stack does not fit at all. The minus 25 C lower limit is worth noting for outdoor equipment, where a pack that is expected to work at minus 30 C needs a different part.

When a pack built around this front end is compared against a newer architecture, the power management cross reference page lists the cell count, the supply range and the bus we compare before proposing a substitute.

The sourcing side of this part is covered on the obsolete part cross reference hub. For a front end that has been in a pack for years, that page covers the alternates we compare when a vendor row changes.

Questions we get on this code

Can this part work as a stand alone protector? It can protect the cells, but it has no gauge and no state of charge output. A pack that needs to report capacity needs a gauge on the same bus, and the pair is the normal arrangement rather than an option.

Is the 2005 document still current? The vendor lists the part as active and in production, and the document has not been revised since 2005 because the silicon has not changed. The orderable row, the reel size and the moisture level are still maintained, which is what a purchase order needs.

Why is the lower temperature limit only minus 25 C? That is the grade this die was qualified to. A pack that must operate below that needs a part with a wider rating, and the substitute will almost certainly have a different pinout, so the board changes with it.

Does the balancing drive need external resistors? Yes. The part provides the drive, and the current that flows during balancing is set by the external path. A balancing current that is too high shows up as heat in the cell area, which is the last place a pack can afford it.