BQ25886RGER
Product Specifications
BQ25886RGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25886RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25886RGER: Standalone two cell boost charger with PowerPath and USB detection in a 4 mm QFN
BQ25886RGER is a 2 A boost mode battery charger in the 24 pin RGE body that lifts a 4.3 V to 6.2 V adapter up to an 8.8 V two cell pack, switches at 1.5 MHz and holds the system rail up through a narrow VDC path in a VQFN-24 body of 24 pins. The BQ25886 is a standalone charger for two cell lithium ion and lithium polymer packs, with the charge voltage, charge current and input current limit all set by resistors rather than by a host. It integrates the switching devices, the current sensing and the loop compensation, runs at 1.5 MHz, and provides a 5 V boost output in the reverse direction for USB on the go. A 17 milliohm battery discharge switch keeps the pack on the system rail without an external path.
Order code and package
| Order code | BQ25886RGER |
| Battery configuration | 2 cells in series |
| Charge current range | 100 mA to 2200 mA, set on ICHGSET |
| Charge voltage options | 8.2 V, 8.4 V, 8.7 V and 8.8 V, set on VSET |
| Input voltage, operating | 4.3 V to 6.2 V |
| Input voltage, absolute maximum | 20 V |
| Input current limit | 500 mA to 3.3 A |
| Switching frequency | 1.5 MHz |
| Interface | standalone, no host required, plus USB D+/D- detection |
| Package | 24 pin VQFN, RGE body, 4 mm by 4 mm |
Electrical parameters that decide the application
| Charge efficiency | 93.4 percent at 5 V in, 7.6 V battery, 1 A charge |
| Charge voltage accuracy | plus or minus 0.5 percent |
| Charge current accuracy | plus or minus 5 percent |
| Input current accuracy | plus or minus 7.5 percent |
| Battery discharge switch | 17 milliohm |
| Minimum input current setting | 500 mA, lower values not supported on ILIM |
| Charge current, ICHGSET shorted | clamped to 30 mA typical |
| Charge current, ICHGSET floating | charge disabled |
| Termination current floor | 10 mA typical |
| Bootstrap capacitor, SW to BTST | 47 nF |
| Input current limit law | IIN equals KILIM times VILIM divided by RILIM times 0.8 V |
| PowerPath | narrow VDC with battery supplement |
Points to check before this part goes on a BOM
Two amps of charge current at 8.4 V is 16.8 W delivered to the pack, and at 93.4 percent efficiency that is 1.19 W of loss and 18 W drawn from the adapter. From a 5 V adapter that is 3.6 A of input current, which is above the 3.3 A maximum input limit, so the full 2 A charge rate is not reachable from a 5 V source at the minimum end of the adapter range. The rate that is reachable is set by the input limit, and the arithmetic is worth doing before a pack is specified as charging in a given time: at 3.3 A and 5 V the input power is 16.5 W, which at 93 percent is 4.6 A of charge current into a 3.6 V per cell pack, so the limit is the input current and not the charger.
The charge voltage is coded by a resistor from VSET to ground, and the four codes are 8.2 V, 8.4 V, 8.7 V and 8.8 V. The mapping is not monotonic in resistance: 18 kohm gives 8.2 V, 39 kohm gives 8.8 V, 75 kohm gives 8.7 V and an open pin gives 8.4 V. A resistor value that has drifted or a pin with flux residue therefore does not fail safe to the lowest voltage, it can land on 8.8 V, which is 4.8 percent above the standard 8.4 V termination of a two cell pack. On a product that charges unattended, that is a cycle life question rather than a field failure, so the code is worth measuring at first article.
The charge current is set on ICHGSET over 30 mA at 114 ohm to 2.2 A at 8 kohm, with the termination current following at a tenth of the programmed value and floored at 10 mA. Shorting the pin clamps the current to the minimum, and leaving it open disables charging altogether, which is a useful property for a product that has to ship with the charger inhibited by a single omitted resistor. A 1 percent part in that position is not optional: the current regulation accuracy of 5 percent is quoted against the pin voltage, so the resistor tolerance adds directly to the delivered current.
The input current limit is a transconductance loop rather than a fixed threshold. The pin voltage is regulated to 0.8 V and the input current follows KILIM times the pin voltage divided by the resistor times 0.8 V, so the resistor is the only component that sets the limit and the loop handles the rest. The limit floor is 500 mA and the pin must not be floated. That floor matters on a USB 2.0 port, which is allowed 500 mA: the part can hold a compliant port at its limit but cannot be set below it, so a product that draws less than 500 mA has to be limited elsewhere or accept the port limit as the operating point.
The input current optimizer is the part of the charger that most teams never think about and most field returns come from. It walks the input current up until the adapter voltage starts to collapse and then backs off, which lets a product pull more than the nominal rating of an adapter that is not actually rated for what its label says. The behaviour is useful with cheap adapters and confusing on a bench supply with a current limit set low: the optimizer hunts, the supply folds back, and the charger settles at a low current that looks like a fault. A bench test should therefore use a supply with headroom above the expected input limit.
The narrow VDC path keeps the system rail above a minimum while the pack voltage is below it, so the load runs from the adapter through the inductor rather than from the pack. With no battery fitted the same path powers the load, which is what allows a product to boot on the bench with the pack disconnected. When the load exceeds what the adapter can supply, the battery discharge switch supplements it through 17 milliohm, which at 2 A is 34 mV of drop and 68 mW of loss, so the switch does not need a heatsink and does not need a parallel path.
The 20 V absolute maximum on the input is not an operating range, and the gap between the two numbers is where products fail. The charger operates from 4.3 V to 6.2 V, so a 12 V adapter plugged into the same connector is inside the survival rating and outside the operating range: the part does not charge, and it does not necessarily protect the system rail either. A product with a barrel jack that accepts more than one adapter should protect the input with something that clamps before the charger's own limit is reached.
Where this order code fits
This order code belongs in wireless speakers, smart speakers, portable point of sale terminals, IP cameras and portable printers, where a two cell pack has to charge from a 5 V USB adapter and the product has to run while it charges. It is also the part chosen where the system rail must come up with no battery fitted at all, because the narrow VDC path powers the load from the adapter through the same inductor that charges the pack. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Can the charger run with no battery connected? Yes. The narrow VDC path powers the system from the adapter through the switching stage, so the product boots and runs with the pack removed. The battery discharge switch is off in that state, and the charge loop reports the missing pack as a termination condition, which is why a bench test with no battery shows a system that runs and a charger that does not charge.
What limits the charge current from a 5 V adapter? The input current limit, not the charge current setting. Two amps into an 8.4 V pack needs about 18 W from the adapter, which at 5 V is 3.6 A, above the 3.3 A maximum input limit. The charger will hold the input at its limit and the charge current will settle below the programmed value. Raising the adapter voltage or lowering the pack voltage is what recovers the full rate.
Is the VSET resistor value critical? It sets the termination voltage and the codes are not in resistance order, so a value that is out of tolerance can move the pack to a different termination level rather than to a safer one. A 1 percent part measured at first article is the cheap check, and the pack temperature sensor input is the second line of defence.
What happens if the input current limit pin is left open? The limit loop has no reference and the charger does not regulate input current, which is outside the intended operating condition and can overload the adapter. The document is explicit that the pin must not be floated. A board that wants a fixed 500 mA limit should fit the resistor for it rather than rely on an internal default.
SUPERB holds and sources this charger line against the exact order code, with the reel, date code and country of origin stated on the offer. When a supply chain has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.