BQ25883RGER
Product Specifications
BQ25883RGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25883RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25883RGER two cell boost mode charger with power path for USB input
The BQ25883RGER charges a two cell lithium pack from a USB adapter and keeps the system alive while it does so. It is a synchronous boost charger running at 1.5 MHz, with a narrow voltage direct current power path, so the system rail stays regulated even when the pack is flat or missing. Everything needed for the conversion, including the FETs, the current sense and the loop compensation, is inside the 24 pin VQFN body.
The input window is 3.9 V to 6.2 V with a 20 V absolute maximum, which is what allows a plain 5 V adapter to charge an 8.4 V pack through a boost stage. Input current limit is adjustable from 500 mA to 3.3 A in 100 mA steps, so the same board can be certified on a USB 2.0 port at 500 mA and on a 3 A adapter without a hardware change. The OTG path runs the converter backwards to feed 4.5 V to 5.5 V out of the battery at up to 2 A.
Key parameters taken from the BQ25883RGER document
| Function | 2-cell boost mode charger with NVDC power path, I2C control |
| Package | VQFN-24, 4.00 mm by 4.00 mm |
| Input range | 3.9 V to 6.2 V operating, 20 V absolute maximum |
| Switching frequency | 1.35 MHz to 1.65 MHz, 1.5 MHz typical |
| Fast charge current | up to 2 A, 5 percent current regulation |
| Charge voltage accuracy | plus or minus 0.5 percent |
| Input current limit | 500 mA to 3300 mA in 100 mA steps, 7.5 percent regulation |
| Input voltage regulation | 3.9 V to 5.5 V, maximum power tracking |
| Battery discharge FET | 17 mOhm, used for supplement mode |
| OTG output | 4.5 V to 5.5 V adjustable, up to 2 A, 94 percent at 5 V and 1 A |
| OTG exit threshold | 6.0 V nominal on a falling battery, 5.85 V to 6.15 V window |
| Monitoring | 16 bit ADC for bus voltage and current, each cell, charge current, system voltage, NTC and die temperature |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The efficiency numbers are the ones to quote to a customer, and they are conditional. 93.4 percent is stated at a 5 V adapter, a 7.6 V battery and 1 A of charge current, and 94 percent for OTG at 5 V and 1 A. A board that charges at 2 A into 8.4 V will run lower, and the thermal path in a sealed enclosure decides whether the part can hold 2 A at all. The 10.7 degrees per watt junction to ambient figure is for the package on a JEDEC board, not for a real case.
Narrow voltage direct current power path is the reason this part suits products that must boot with a dead pack. The system rail is held above the battery minimum, the pack is topped up separately, and in supplement mode the battery makes up the difference when the adapter cannot deliver a peak. That behaviour is what lets a 5 V 2 A adapter run a product that pulls 3 A for a second at a time.
Input current optimisation runs automatically when enabled. It walks the input current limit down until the adapter voltage stops collapsing, which recovers the maximum a poorly specified charger will actually give. On a bench supply this looks like nothing is happening; on a cheap wall wart it is the difference between charging and oscillating.
The OTG threshold has a real consequence. Boost mode stops when the battery falls to about 6.0 V, so a two cell pack in OTG service is effectively a 6 V pack with a narrow usable window above it. Products that use OTG heavily should size the pack for the cutoff, not for the 8.4 V top end.
- Charge is enabled and disabled over I2C, and the CE pin can hard stop it, which gives the host two independent ways to kill charge current.
- The integrated 16 bit ADC reads each cell voltage, which removes the external divider and the calibration step that goes with it.
- D plus and D minus auto detection covers SDP, CDP, DCP and non standard adapters, so a single board can ship with several cables.
- The battery FET is 17 mOhm, so supplement mode does not give away much efficiency compared with a direct connection.
Which projects this part fits
This charger fits two cell products with a USB input and a system rail that must stay on: Bluetooth speakers, portable POS terminals, label and receipt printers, wireless security cameras and medical carts that run from a 2s pack. If the product must also power accessories from the battery, the OTG path removes a separate boost converter. The power management cross reference table lists the two cell charger families we keep in stock, and the component lead time page explains how we hold allocation on charger ICs that go short every second quarter.
Ordering, siblings and the first article test list
The BQ25883RGER is the 24 pin VQFN version in a 4.00 mm by 4.00 mm body. The balancing sibling shares that body and that pinout, so a board can move between the two chargers without a board change, but a board cannot move to the older 16 pin generation without one. That distinction matters when a customer sends a board file and asks for the nearest available charger.
| Check on the first article | Limit to hold |
| Input current limit at the default setting | Within the 7.5 percent regulation window at the chosen step |
| Charge current at 1 A and at 2 A | Within 5 percent at 1 A, wider at low current where the document prints a 15 percent window |
| Charge voltage at the pack terminals | Within 0.5 percent, measured at the pack, not at the charger output |
| OTG output at 5 V into 1 A | Within 3 percent, with the battery above the 6.0 V exit threshold |
| Case temperature at 2 A charge in the real enclosure | Below the thermal regulation point, or the current fold back is documented |
The inductor is the component that most often fails this list. A part rated at 2 A of saturation current is not enough for a 2 A charge current in a boost converter, because the switch current is higher than the average output current and the ripple sits on top of it. A saturated inductor shows up as a current that will not reach the set point and a case that runs hot, which reads like a charger fault.
Questions that come up before a purchase order is released
Can the system run with no battery fitted?
Yes. The power path keeps the system rail regulated from the adapter alone, and the charger reports the missing pack through status registers. That is the normal bench condition during board bring up, and the part is specified for instant on in that state rather than treating it as a fault.
What limits the 2 A charge current in practice?
Thermal rise in the actual enclosure, the adapter's own current limit, and the input current limit setting. The part folds back charge current when the die reaches its thermal regulation point, so a board that only works on an open bench will simply charge slower in a closed case. The 20 V input rating protects against a wrong adapter, not against continuous operation above 6.2 V.
Is the 1.5 MHz switching frequency fixed?
The oscillator is specified from 1.35 MHz to 1.65 MHz with 1.5 MHz typical, and the part runs at that frequency in both charge and OTG mode. That is what allows a small inductor, but it also means the input filter has to be laid out for 1.5 MHz and its harmonics rather than for a 500 kHz converter.
How SUPERB handles this line
We supply the BQ25883RGER on the large reel with lot traceability, and we can quote the matching inductor and input capacitors as one kit so the charger and its passives arrive together. If a product is moving from a linear charger to this part, the adapter specification usually has to change as well; send us the adapter list and the pack specification and we will check both against the input window before the first order. The drop in replacement check page covers the pin by pin comparison we run for changes like this.