Contact Us

BQ25713RSNR

Brand: Texas Instruments
Texas Instruments BQ25713RSNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25713RSNR — Power Management & Signal Chain | Superb Automation

BQ25713RSNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25713RSNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25713RSNR: I2C buck boost charge controller for 1S to 4S packs with pass through mode

BQ25713RSNR is a narrow VDC buck boost battery charge controller in a WQFN body of 32 pins. The part is the I2C member of the buck boost charger family, answers at address 6Bh, and adds pass through mode plus an 8 mV charge voltage grid over the BQ25703A it is pin compatible with. It charges any pack from 1S to 4S from a source between 3.5 V and 24 V and monitors input current, battery current and system power for processor throttling.

Order code and package

Order codeBQ25713RSNR
PackageWQFN, 32 pins, 4.00 mm by 4.00 mm
Input voltage, operating3.5 V to 24 V
Battery1S to 4S Li-ion
Host interfaceI2C, address 6Bh
Sibling addressBQ25713B answers at 6Ah
Power FETsexternal
Compatibilitypin and software compatible with BQ25703A

Electrical parameters that decide the application

Charge voltage accuracyplus or minus 0.5 percent
Charge voltage step8 mV
Charge current accuracyplus or minus 2 percent
Current monitor accuracyplus or minus 2 percent
Power monitor accuracyplus or minus 4 percent
OTG output range3 V to 20.8 V, 8 mV step
OTG current limitup to 6.4 A, 50 mA step
Pass through modesupported

Points to check before this part goes on a BOM

The I2C address is 6Bh, and the BQ25713B answers at 6Ah. That one bit of difference is what lets two packs share a bus, and it is the only reason to choose the B version on a new board; an image written for 6Bh will not reach a 6Ah device and the host will read an acknowledge failure rather than a wrong value, which is the easier of the two faults to diagnose.

The charge voltage grid is 8 mV here against 16 mV on the BQ25703A this part replaces. A register value copied across from an older image therefore commands about half the intended voltage, so the value has to be recomputed from the new resolution rather than moved with the rest of the register map.

The OTG output runs from 3 V to 20.8 V at 8 mV resolution, while the BQ25703A stops at 4.48 V with a 64 mV grid. A product that charges a 1S accessory or powers a 3.3 V peripheral from the pack gains the low end of that range and an eight times finer step, which is what makes a 5 V USB port stay inside its own tolerance.

Charging a 4S pack at 3 A is 50.4 W. From a 5 V USB source at 90 percent that is 11.2 A of input, well above the 6.4 A limit and beyond what a 5 V connector will carry, so a 5 V adapter can only top up a 4S pack at a fraction of the current a 20 V adapter delivers. The 3.5 V to 24 V input range describes the converter, not a promise that every source can charge every pack at full rate.

The power monitor is plus or minus 4 percent while the current monitors are plus or minus 2 percent. A host that throttles on the power number inherits the wider error, which on a 65 W system is 2.6 W, so the throttle threshold needs more margin than the current-based one.

Pass through mode connects the adapter to the system without switching when the adapter window allows it. In a drone or an IP camera that idles on a mains adapter, most of the operating hours are spent in that mode, and the efficiency claim for the product rests on it rather than on the peak buck boost number.

Four external FETs and an inductor carry the whole current, so the 32-pin body dissipates only its own gate drive and housekeeping; the thermal question moves to the FETs and the inductor. The input and battery current limits in the register set are settings for those parts, and the part will happily command a current the FETs cannot survive if the board was sized from the register range.

The current and voltage registers can be written while charging, so a host can follow a JEITA style profile without stopping the loop. The part also holds a PROCHOT profile that is IMVP8 and IMVP9 compliant, which is what a notebook chipset expects when it decides to drop processor power.

Charge current accuracy of plus or minus 2 percent at a 3 A setting is 60 mA, and at the 6.4 A limit it is 128 mA. A pack whose datasheet gives a maximum charge current with no margin needs the register set below that maximum by at least the accuracy plus the sense resistor tolerance, because the two add and the resistor is usually the larger term.

There is no JEITA pin on this part. The temperature profile is applied by the host writing new voltage and current limits after it reads the thermistor, so the host has to stay awake through the whole charge and a product that sleeps during charge will hold the last written profile regardless of pack temperature.

Twenty-four volts on a 0.4 mm pitch package leaves very little room for a hot plug transient. The input clamp belongs at the connector rather than next to the part, and the input capacitor has to be close enough that the inductance between it and the FETs does not turn the clamp voltage into a ring the FETs have to survive.

Where this order code fits

Drones, Bluetooth speakers, IP cameras, detachable tablets and power banks that must charge a 1S to 4S pack from any adapter they are handed are the applications for this controller. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is it a drop in for the BQ25703A? The package and the pinout match, and the vendor states software compatibility, but the charge voltage resolution and the OTG range differ, so the register values have to be recomputed for the finer grid before an existing image is reused.

How is the pack current measured? Through a sense resistor on the battery side with the result reported to the host over I2C at plus or minus 2 percent, and the same signal feeds the current limit loop, so the resistor tolerance is part of the charge current accuracy.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.