BQ25710RSNR
Product Specifications
BQ25710RSNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25710RSNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25710RSNR: SMBus buck boost charge controller for 1S to 4S packs with system power monitoring
BQ25710RSNR is a narrow VDC buck boost battery charge controller in a WQFN body of 32 pins. The part moves between buck, buck boost and boost without a mode command, so one board charges a 1S pack from a 20 V adapter and a 4S pack from a 12 V adapter, and it reports input current, battery current and system power to the host for processor throttling.
Order code and package
| Order code | BQ25710RSNR |
| Package | WQFN, 32 pins, 4.00 mm by 4.00 mm |
| Input voltage, operating | 3.5 V to 24 V |
| Battery | 1S to 4S Li-ion |
| Conversion | buck, buck boost and boost, seamless |
| Host interface | SMBus, address 09h |
| Power FETs | external |
| Compatibility | pin and software compatible with BQ25700A |
| Throttling | PROCHOT profile, IMVP8 and IMVP9 |
Electrical parameters that decide the application
| Charge voltage accuracy | plus or minus 0.5 percent |
| Charge voltage step | 8 mV |
| Charge current accuracy | plus or minus 2 percent |
| Current monitor accuracy | plus or minus 2 percent |
| Power monitor accuracy | plus or minus 4 percent |
| OTG output range | 3 V to 20.8 V, 8 mV step |
| OTG current limit | up to 6.4 A, 50 mA step |
| Pass through mode | supported |
Points to check before this part goes on a BOM
The SMBus address is 09h, which is the same address as the BQ25700A, the BQ25708 and the BQ25718. Two of these on one bus cannot be told apart, so a product with two packs needs a bus segment each or the I2C siblings, where the BQ25713 answers at 6Bh and the BQ25713B at 6Ah.
Eight millivolts per step on a 4S pack means a 16.8 V setpoint is code 2100, and the step is 0.05 percent of the setpoint while the accuracy is 0.5 percent. The fine grid is there for a host that tracks temperature compensation, not for the initial accuracy, which is ten times coarser.
A 4S pack at 16.8 V from a 12 V adapter is boost, from a 20 V adapter is buck, and from an 18 V adapter sits near unity where the part runs buck boost. The same board therefore covers a 12 V car adapter and a 20 V USB PD source, which is the reason to choose this part over a plain buck controller.
The OTG path is specified from 3 V to 20.8 V with 8 mV resolution, and the current limit goes to 6.4 A in 50 mA steps. At 20.8 V and 6.4 A that register setting describes 133 W, which no 4 by 4 mm package can pass; the limit is a setting for the external FETs and the inductor, so the OTG power has to be taken from the FETs and the thermal path rather than from the register range.
The power monitor is plus or minus 4 percent, twice the error of the current monitors. On a 65 W system reading that is 2.6 W, which is a large step for a host that throttles the processor on the reported number, so the throttling thresholds need to sit further from the adapter rating than 4 percent.
Pass through mode ties the adapter to the system without switching when the adapter window allows it. That is where the light load efficiency comes from in a notebook that idles at a few hundred milliamps, and it also means the input current is no longer shaped by the charge loop, so the adapter current limit has to be trusted by the host.
No power FETs are integrated, so 3.5 V to 24 V is the controller range and the FETs see the adapter transient. A 24 V input leaves almost no headroom for a hot plug ring on a 20 V source, and the inductor overcurrent protection protects the switch rather than the connector.
Instant-on with no battery holds the system at the battery voltage or above a programmable minimum, so a notebook with a removed pack still boots. The battery FET then works as an ideal diode in supplement mode, which is where the 2 percent current monitor accuracy matters, because the host decides whether the adapter is overloaded from that reading.
The part asserts PROCHOT to the processor when the adapter current crosses a programmed threshold, which is how a notebook keeps its adapter inside its rating when a turbo burst pulls more than the charger can pass. The threshold is a register value derived from the sense resistor, so the profile is only as accurate as the 2 percent current monitor it is built on.
Eight millivolts per step on a 1S pack puts 4.20 V at code 525 and makes the low end of the range usable for a 3.7 V chemistry, while the same field on a 4S pack covers the 16.8 V setpoint. One register set therefore serves every pack size in the family, which is what allows a single firmware image across a product line.
The OTG floor of 3 V is what lets the port supply a 3.3 V peripheral directly from a pack that is nearly flat, with 300 mV of headroom. At the top end 20.8 V covers a 4S accessory, so the same port can charge the product's own spare pack or run a 3.3 V sensor board without a second converter.
Where this order code fits
Notebooks, detachable tablets, power banks and industrial or medical equipment that must charge any pack between 1S and 4S from any adapter between 3.5 V and 24 V are the applications for this part. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it need a separate boost for USB OTG? No. The same four FETs run as a boost for the OTG path, with the output programmable from 3 V to 20.8 V, so a USB port can be powered from the pack without a second converter.
Can the host change the charge current while charging? Yes, the current and voltage registers are writable at any time and the loop takes the new value on the next cycle; the part does not need to stop charging for a register update.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.