Contact Us

BQ25171QWDRCRQ1

Brand: Texas Instruments
Texas Instruments BQ25171QWDRCRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25171QWDRCRQ1 — Power Management & Signal Chain | Superb Automation

BQ25171QWDRCRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25171QWDRCRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25171QWDRCRQ1: automotive 800 mA linear charger for one or two cells and for nickel metal hydride packs

BQ25171QWDRCRQ1 is a linear charger that holds a pack at a resistor set voltage from 3.5 V to 8.4 V and supports both lithium and nickel chemistries on the same board in a VSON body of 10 pins. The part is qualified to AEC-Q100 grade 1 and takes 3 V to 18 V in with 40 V of load dump tolerance, so it can charge a backup pack directly from a vehicle rail. The regulation voltage is set by two resistors on VSET, the current by one resistor on ISET, and the chemistry and the timer by a resistor on CHM_TMR. The DRC body is 3.00 mm by 3.00 mm.

Order code and package

BQ25171QWDRCRQ1VSON DRC, 10 pins, 3000 pieces on a large reel, NIPDAU, Level-2-260C-1 YEAR
BQ25171QWDRCRQ1.Alabel row of the same body and reel, same finish and moisture level
QualificationAEC-Q100 grade 1, minus 40 to plus 125 C ambient, HBM level 2 and CDM level C4B
Chemistriesone or two cell Li-ion, Li-polymer and LiFePO4, and one to six cell NiMH in constant current
Body size3.00 mm by 3.00 mm, ten pins, exposed pad
Output rating13 V absolute maximum at OUT, which is what limits the two cell lithium setting to 8.4 V

Electrical parameters that decide the application

Input range3.0 V to 18 V operating, 40 V absolute maximum for load dump, with the trip at 18.4 V
Charge voltage3.5 V to 8.4 V set by the VSET divider, plus or minus 0.5 per cent
Charge current10 mA to 800 mA, set as KISET over RISET with KISET of 300 Aohm, so 375 ohm gives 800 mA and 30 kohm gives 10 mA
Current accuracyplus or minus 10 per cent, with the precharge at 20 per cent of the set current
Termination10 per cent of the set current on a lithium pack, or the timer on a nickel pack
Leakage350 nA from the pack with the input absent, 2 uA from the input while charging is disabled
Dropout425 mV at 500 mA, which is the headroom a 5 V rail needs to hold a 4.2 V pack
Thermistor38 uA of bias on TS, 103AT-2 curve recommended, charge suspended outside the window
Thermal behaviourregulation at 125 C and shutdown at 150 C, with the current reduced rather than cut
TimersCHM_TMR sets both the chemistry and the charge timer duration, so one resistor decides two things

Family variants and how they differ

Lithium against nickelthe same part terminates on current for a lithium pack and on time or on the output overvoltage for a nickel pack, and the CHM_TMR resistor selects which
One cell against twothe VSET divider covers 3.5 V to 8.4 V, so a two cell pack at 8.4 V is inside the range and the same board serves both with a different divider
Automotive against industrialthe Q1 suffix is the AEC-Q100 part with grade 1 temperature, and the industrial member of the family stops at a lower ambient
Load dump tolerance against operating rangethe input survives 40 V for the load dump event, but regulation is only specified to 18 V, so the pack is protected and not charged during the event
Integrated termination against a host commandthis part ends the cycle by itself, which is what an always on backup charger needs, and offers the CE pin for a host that wants control
VSON against the larger bodiesthe ten pin 3 mm body moves heat through the pad, and at 800 mA from 13 V into a 7 V pack the dissipation is above 4 W, so the copper is part of the current rating

Points to check before this part goes on a BOM

A linear charger on a vehicle rail is a heater. At 13.5 V in and a 7.4 V pack at 800 mA the part dissipates about 4.9 W, and no 3 mm body survives that in a sealed module. The part protects itself by folding back the current, so the real charge rate on a two cell pack from the vehicle rail is set by the thermal path and not by the ISET resistor. A product that needs the full 800 mA has to limit the input voltage or move to a switch mode part.

The VSET divider sets a voltage, not a chemistry. A two cell lithium pack and a six cell nickel pack can share the same window, and the difference in behaviour comes entirely from CHM_TMR. A board that changes the pack type without changing that resistor holds a nickel pack at a lithium voltage, which is the failure mode worth writing into the assembly instruction.

A nickel pack needs a different termination rule. The part runs constant current and ends on the timer or on the output overvoltage, because a nickel cell has no voltage plateau to detect. A product that expects a current taper will report a pack that never finishes, and the timer is the only thing that ends the cycle.

The 350 nA pack leakage is the reason this part exists. A backup pack in a vehicle module sits for months without the rail, and a charger that leaks a few microamps empties it. The figure is specified with the input absent, which is the condition that matters, and it is an order of magnitude below a typical linear charger.

The thermistor is not optional on a vehicle product. The pack sits next to the engine or in a sun loaded cabin, and the TS window is what stops a charge at 60 C. A board that ties TS to a fixed voltage to avoid the thermistor loses the only protection the part has against charging a hot pack, and the qualification does not cover that configuration.

The dropout is what decides the input rail. 425 mV at 500 mA means a 5 V rail can hold a 4.2 V pack and a 4.5 V rail cannot. On a vehicle rail that dips during cranking, the part stops charging and restarts, and the VIN_LOWV window of 3.05 to 3.15 V rising is what keeps it from chattering at the boundary.

Where the copper decides the rating

The pad under the body is the only thermal path, and the document gives the copper area needed for the full 800 mA at a realistic input voltage. A board that copies the land pattern without the surrounding copper runs the part into thermal regulation within minutes and holds about half the current.

The second thermal detail is the input voltage. The dissipation is the input minus the pack voltage times the current, so the same board behaves very differently on a 5 V rail and on a 13.5 V rail. A module qualified at 5 V and moved to a vehicle rail needs the charge current reduced, not the copper increased.

What to ask a supplier for

Ask for the qualification record with the code, because the Q1 suffix is the automotive part and the same family exists without it. A reel that carries the industrial member will work on the bench and fail the temperature requirement in the module.

Ask also for the moisture level and the date code. This body is published at Level 2 with a one year floor life, and a module built for a vehicle program usually needs the traceability that goes with it.

Where this order code fits

Automotive telematics backup packs, emergency call modules, dash camera supercapacitor and battery backup and industrial instruments that must charge from a 12 V or 24 V rail use this part. The nickel support is what makes it usable in a module that keeps a low cost backup pack rather than a lithium one. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can this part charge a supercapacitor bank? Not by intent. It regulates a voltage and terminates on current, and a capacitor bank looks like a very large cell with no termination point, so the cycle would run to the timer. A capacitor bank needs a current limited source rather than a charger with a termination rule.

What sets the charge timer? The resistor on CHM_TMR sets both the chemistry and the duration, so the timer cannot be chosen independently of the chemistry. A product that needs a longer timer on a large nickel pack changes the resistor and the chemistry together, which is why the two are documented as one table.

Is the output protected if the pack is connected backwards? The OUT pin is rated to 13 V absolute and the part has short circuit protection, but a reversed pack is outside the specified conditions. The connector keying and a series element in the pack are what protect the board, and the qualification does not cover a reversed connection.

Does the part work with the engine cranking? It stops charging when the input falls below the low voltage window and restarts when the rail recovers. The pack is not discharged into the rail because the reverse path is blocked, so a cranking event costs a few seconds of charge rather than a pack.

Why is the current accuracy only 10 per cent? The sense element is internal and the setting is a resistor, so the tolerance covers the resistor, the reference and the amplifier. A product that needs a tighter charge current has to measure it externally, and 10 per cent is adequate for a backup pack where the charge time is measured in hours.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.