BQ24751ARHDR
Product Specifications
BQ24751ARHDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24751ARHDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24751A: a host controlled charger for two to four cells at 10 A
The BQ24751ARHDR is a synchronous buck charge controller with a system power selector, aimed at notebooks and portable instruments. It charges two, three or four Li-ion cells in series at up to 10 A, from an adapter between 5 V and 24 V, with a 300 kHz switching stage that reaches above 95 per cent efficiency.
The controller drives external NMOS switches on both the high and the low side, with a 30 ns minimum dead time and a maximum effective duty cycle of 99.5 per cent. That duty cycle figure is what makes a notebook charger work: when the adapter voltage is close to the pack voltage, the converter has to pass the input almost straight through, and a controller that limits duty to 90 per cent simply cannot charge the pack at the top of its range.
Charge current and voltage are programmed ratiometrically, either by resistors or by the system controller through a DAC or GPIOs. That is what the host controlled label means: the same part can be tuned by hardware on one platform and by software on the next, without a different order code.
Key data for the BQ24751ARHDR
| Function | Synchronous buck charger with system power selector |
| Cell count | Two, three or four cells in series, multi chemistry |
| Charge current | Up to 10 A |
| Switching frequency | 300 kHz nominal, 240 kHz to 360 kHz across the tolerance |
| Efficiency | Above 95 per cent |
| Dead time | 30 ns minimum, 99.5 per cent maximum effective duty cycle |
| Accuracy | Plus or minus 0.5 per cent charge voltage, 3 per cent charge and adapter current, 2 per cent input sense amplifier |
| Quiescent | 7 to 10 microamps off state total, 100 to 200 microamps with the adapter present and charge off |
| Protection | Programmable input OVP, dynamic power management, AC over power protection |
| Package | VQFN, 28 pins, 5 mm by 5 mm thin body |
| Temperature | Minus 40 to 125 C operating |
Body and ordering data
BQ24751ARHDR is the active row: VQFN RHD with 28 pins, 5 mm by 5 mm, 3000 pieces on a large tape and reel, NIPDAU finish, moisture level 2 with a one year floor life at 260 C, minus 40 to 125 C, marking BQ24751A. The text extract of the addendum splits the marking across two columns, so the top line of the table looks incomplete. The .B row carries the same body and quantity.
The A in the string is not cosmetic. The bq24751 and the bq24751A differ in the protection behaviour and in the input sense accuracy, and the two are not interchangeable on a board that relies on the AC over power function.
The system power selector and the AC over power function
In a notebook, the adapter is sized for the average load, not the peak. When the processor boosts and the adapter is already at its limit, the system power selector lets the pack make up the difference, and the rail stays in regulation. The AC over power protection goes further: it reduces the adapter current draw when the adapter is asked for more than it can give, so a 65 W adapter on a 90 W platform throttles instead of collapsing.
Both functions need the input sense resistor and the adapter detection resistor to be set for the actual adapter. A board tuned for a 90 W adapter and then shipped with a 65 W one will throttle constantly, and the user reports a notebook that charges only when it is switched off.
Where it fits in a build
Notebooks, ultra mobile computers, portable data terminals, portable printers, medical diagnostic equipment, battery bay chargers and battery backup systems. The multi chemistry support matters for the last two, where a lead acid or a nickel pack may share a platform with a lithium pack. The power management cross reference page lists the parts we compare on cell count and adapter window.
For a product with a 2 cell pack and 4 A of charge current, a 1.2 MHz integrated controller is smaller and cheaper. The 300 kHz stage here wins when the current is high and the input is close to the pack voltage.
The sourcing side of this part is covered on the pin to pin cross reference. When a notebook platform is compared on this controller against a newer one, that page covers the pins, the sense lines and the register defaults we check first.
Questions we get on this code
Does it charge with no host? Yes, the resistor programming sets the defaults. The host is only needed if the platform wants to change current or voltage at run time.
Why is the 99.5 per cent duty cycle important? Because at the top of the charge the adapter voltage and the pack voltage are close, and a lower duty limit would stop the charge before the pack is full.
What is the off state drain on the pack? 7 to 10 microamps total, which on a 4000 mAh pack is a few years of shelf life rather than a few months.
Can the two current loops fight each other? They are built to work together: the input loop limits adapter current, the charge loop limits pack current, and the lower of the two wins. A board where both are set to their maximum has no protection against an undersized adapter.