Contact Us

BQ24715RGRR

Brand: Texas Instruments
Texas Instruments BQ24715RGRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24715RGRR — Power Management & Signal Chain | Superb Automation

BQ24715RGRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24715RGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24715RGRR: 2S and 3S narrow VDC charger controller with SMBus control and a 100 microsecond transient response

BQ24715RGRR is a narrow VDC battery charge controller for two and three cell packs in a VQFN body of 20 pins. The part drives external N-channel adapter and reverse blocking FETs plus an external P-channel battery FET, so the current path is set by the FETs on the board while the loop, the soft start and the compensation sit inside a 3.50 mm by 3.50 mm body.

Order code and package

Order codeBQ24715RGRR
PackageVQFN, 20 pins, 3.50 mm by 3.50 mm
Input voltage, operating6 V to 24 V
Battery2S or 3S Li-ion
Power FETsexternal, N-channel ACFET and RBFET, P-channel BATFET
Switching frequency600 kHz, 800 kHz, 1 MHz
Host interfaceSMBus
Current monitor40 times input, 16 times discharge

Electrical parameters that decide the application

Charge voltage step16 mV, 11 bit
Charge current step64 mA, 7 bit
Charge voltage accuracyplus or minus 0.5 percent
Charge current accuracyplus or minus 3 percent
Monitor accuracyplus or minus 2 percent
Quiescent current500 microamp
Light load efficiency80 percent at 20 mA
Transient response100 microsecond
Minimum system voltage6 bit, programmable
Adapter detect threshold0.6 V on ACDET

Points to check before this part goes on a BOM

Eleven bits at 16 mV per step spans 32.8 V, so one register field covers every pack this controller serves. On a 2S pack 8.4 V is code 525 and each step is 0.19 percent of the setpoint; on 3S the same step is 0.13 percent of 12.6 V, so the resolution is finer on the larger pack and the 0.5 percent accuracy dominates either way.

Seven bits at 64 mA per step tops out at 8.19 A, and a 4 A charge is 62.5 steps. The reachable values around 4 A are 3.968 A and 4.032 A, so a cell specification written as 4.00 A is either met with 32 mA of margin or exceeded by 32 mA depending on which way the host rounds.

Plus or minus 0.5 percent is 42 mV on an 8.4 V string and 63 mV on 12.6 V. A pack built from cells held to 4.20 V plus or minus 1 percent tolerates 0.5 percent comfortably in 2S, but the same 0.5 percent on 3S uses half of a 0.25 percent per cell budget before the cell tolerance is counted.

The 500 microamp quiescent current is drawn from the adapter, and at 20 V that is 10 mW. The 80 percent light load figure is quoted at 20 mA into an 8.4 V pack, which is 168 mW of output and 210 mW of input, so the controller itself is 4.8 percent of the input power at that point and the efficiency figure only holds above a few milliamps of charge.

The input monitor multiplies by 40 and the discharge monitor by 16. At the 64 mA register step the monitor output moves 2.56 V per step multiplied, so one LSB of charge current is 0.27 percent of a 3.3 V converter range; a host that reads the monitor to compute remaining runtime is reading a signal that gains 40 times the sense resistor drop and clamps near the rail long before the current limit.

With no power FETs inside, the 6 V to 24 V figure is a controller rating and not a pass element rating. The adapter FET sees the full hot plug transient, and the 4 kohm resistor in series with the ACDRV gate drive is what holds the in-rush into the input capacitors to a slope the adapter can survive.

At 800 kHz the period is 1250 ns, and 24 V in to 8.4 V out is a 35 percent duty cycle or 437 ns of on time. The 100 microsecond transient response is 80 of those periods, which is why the output capacitor bank is sized by the load step and not by the ripple, and why a 600 kHz setting buys switching loss back only if the inductor is large enough to carry the same ripple.

Instant-on with no battery or a deeply discharged battery comes from the narrow VDC loop holding the system at the battery voltage but never below the programmable system minimum. That floor is a 6 bit field, so a product that wants 9.0 V on a 3S pack has to accept the nearest code rather than an arbitrary value, and the charge current has to be re-issued after every adapter change.

Adapter detection works off a 0.6 V threshold on the ACDET pin. A divider that puts 0.6 V on that pin at a 6 V adapter leaves 1.9 V at 19 V and 2.4 V at 24 V, both inside the pin range, so one divider covers the whole 6 V to 24 V span and the same board works with a 12 V and a 20 V adapter without a component change.

The LEARN function discharges the pack into the system so the gauge can see a full cycle. On a product with a small system load the discharge takes hours, and the host has to keep the machine awake for the whole sequence, so the function belongs in a service menu rather than in a background task.

The gate drive power is not in the 500 microamp quiescent figure. Thirty nanocoulombs of gate charge at 12 V and 800 kHz is 0.29 W of drive loss per FET, and with an adapter FET, a reverse blocking FET and a battery FET on the board the driver is dissipating close to a watt before any current flows to the pack.

Where this order code fits

Notebooks, ultrabooks, tablets, and industrial or medical equipment that carries a 2S or 3S pack and wants the charge loop and the FETs kept separate are the usual applications for this controller. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it work from a 5 V input? No. The operating input floor is 6 V and the adapter detect threshold sits at 0.6 V on ACDET, so a 5 V rail is below the range in which the part is specified even if a divider makes ACDET read correctly.

Is the current monitor fast enough to throttle a CPU? It is an analogue output with no sampling, so the host sets the reaction time by its own ADC; the limitation is the 2 percent accuracy and the 40 times gain, not a conversion rate.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.