BQ24381DSGR
Product Specifications
BQ24381DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24381DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24381: a front end protection part, not a charger
The BQ24381DSGR sits between the charging source and the rest of the product and does one job: it disconnects a bad source before the bad source reaches the battery. The input is rated to 30 V. The output is regulated to 5 V for the bq24381 and the bq24382, and to 5.5 V for the bq24380, for any input above that level, which is what the document calls LDO mode.
Three things trip it. Input overvoltage, where the pass FET opens immediately and the charging circuit is isolated. Battery overvoltage, where power is removed from the system if the pack voltage rises past the threshold. And output short circuit, checked each time the pass FET turns on, with a recheck cycle rather than a latch. A die temperature of about 140 C also switches it off.
The soft start and soft stop are not decoration. A pass FET switched into a discharged output capacitor draws a current step limited only by the FET resistance and the source impedance, and on a 30 V source that step is large enough to damage connectors and to reset the product through the rail. Ramping the gate limits both.
Key data for the BQ24381DSGR
| Function | Charger front end protection with LDO mode output |
| Input rating | 30 V maximum input |
| Output regulation | 5 V for the bq24381 and bq24382, 5.5 V for the bq24380 |
| Load current | Up to 1.7 A |
| Overvoltage | Input OVP with hysteresis, battery OVP at about 4.35 V typical |
| Short circuit | Detection threshold 1.3 A to 1.7 A, with automatic recheck |
| Soft start | Gate ramp to limit inrush into the output capacitance |
| Thermal | Shutdown above about 140 C die temperature |
| Control | Enable input and fault status output |
| Package | WSON, 8 pins, 2 mm by 2 mm |
| Temperature | Minus 40 to 125 C operating |
Body and ordering data
The family is bq24380, bq24381 and bq24382. The orderable row for this page is BQ24381DSGR, WSON DSG with 8 pins, 3000 pieces on a large tape and reel, NIPDAU or NIPDAUAG finish, moisture level 2 with a one year floor life, minus 40 to 125 C. The printed addendum rows are worth reading carefully, because the status and finish columns sit under different headers in the text extract and the first line of the table looks blank.
The three members differ mainly in the regulated output level and in the overvoltage threshold. A 5 V output feeding a charger that expects 5.5 V loses headroom, and a 5.5 V output feeding a 5 V only charger puts the charger at the top of its window. The choice follows the downstream part, not the battery.
Why the protection threshold is not the same as the charger threshold
A charger with its own 6.5 V input protection already survives a 6 V adapter, and adding a front end part at 5.5 V means the front end trips first and the product looks dead on a legitimate source. The two thresholds have to be ordered: the front end protects against a gross fault, the charger protects against a modest one, and the front end threshold sits above the highest legitimate input.
The battery overvoltage function is separate and protects the pack rather than the input. If the charger loop fails and the cell voltage climbs past about 4.35 V, this part removes power from the system. That is a redundant protection layer, and in a product with a permanently installed pack it is the layer that keeps a single component failure from becoming a fire.
Where it fits in a build
Phones, PDAs, media players and low power handhelds that charge from a connector the user can plug anything into. It is also used on products with a removable pack where the pack itself has no protection board. The power management cross reference page lists the front end parts we compare on threshold and output level.
A product with a fixed, non user accessible adapter and a protected pack does not need this part, and adding it costs 2 mm by 2 mm plus the voltage drop of the pass FET at 1.7 A.
The sourcing side of this part is covered on the date code management. For a protection part that sits on the shelf between builds, that page sets out how we track date codes and what we will not ship into a new run.
Questions we get on this code
Is this a charger? No. It has no charge algorithm, no current regulation into the cell and no termination. It protects a charger that is downstream of it.
What is the voltage drop at 1.7 A? It is the pass FET resistance times the current, and the document gives the resistance in the electrical table. On a 5 V rail that drop is the difference between a charger that reaches its full current and one that does not.
Does the short circuit protection latch? No, it rechecks. A latch would need a power cycle or a host command to clear, and on a product with no host that would leave the unit dead until the battery ran out.
Can it protect a 12 V input? The 30 V rating allows the input to survive 12 V, but the output regulates at 5 V or 5.5 V and the pass FET dissipates the difference. At 1.7 A from 12 V that is around 11 W in a 2 mm package, which the thermal shutdown will not allow.