Contact Us

BQ24295RGER

Brand: Texas Instruments
Texas Instruments BQ24295RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24295RGER — Power Management & Signal Chain | Superb Automation

BQ24295RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24295RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24295RGER: I2C controlled 3 A single-cell charger with boost mode

BQ24295RGER is a switch-mode single-cell charger with narrow-VDC power path and a boost output in a VQFN body of 24 pins. It charges one cell at up to 3 A from a 3.9 V to 6.2 V input, sets input current limits from 100 mA to 3 A over an I2C bus, holds charge voltage to plus or minus 0.5 percent and charge current to plus or minus 7 percent, and boosts the cell back to 4.55 V to 5.5 V at 1.5 A for a USB output.

Order code and package

Ordering stringBQ24295RGER, RGE package, tape and reel
Package24-pin VQFN, 4.00 mm by 4.00 mm
Thermal resistance32.2 C/W junction to ambient
ControlI2C port for current limits, voltage and status
CellOne lithium-ion or lithium-polymer cell, 4.2 V regulation

Electrical parameters that decide the application

Input range3.9 V to 6.2 V, with 6.4 V input overvoltage protection
Charge currentUp to 3 A, switch mode at 1.5 MHz
Input current limits100 mA, 150 mA, 500 mA, 900 mA, 1 A, 1.5 A, 2 A and 3 A
Charge accuracyPlus or minus 0.5 percent on voltage, plus or minus 7 percent on current
Boost output4.55 V to 5.5 V adjustable at 1.5 A
PathNarrow-VDC management, system runs with no battery or a deeply discharged one
Leakage20 microamp battery leakage in shipping mode

Points to check before this part goes on a BOM

A switch-mode charger exists to keep the dissipation out of the product. Charging a 3.7 V cell from 5 V at 3 A is 3.9 W in a linear topology and about 0.5 W in this one at 90 percent efficiency, which is the difference between a hot spot in a 4 mm package and a warm board. The inductor is the price: 1.5 MHz allows a low-profile part at 1.2 mm, and its saturation current has to cover the 3 A plus ripple.

Eight input current limits from 100 mA to 3 A, set over the bus, are the protocol surface of the product. A host that has enumerated a USB 3 port can ask for 900 mA; a dedicated charger can be asked for more; a weak adapter should be limited by the maximum power tracking that watches the input voltage. The limit is a number in a register, so it can be wrong in firmware without any hardware difference, which is why the register default matters at boot.

Narrow-VDC power path keeps the system rail just above the cell voltage instead of at the input voltage, so the downstream regulator does not dissipate the difference. It also lets the system start with a fully discharged cell, because the path can supply the system while the cell is below its minimum. The trade is that the system rail moves with the cell, so anything expecting a fixed 5 V has to be behind a regulator.

Boost mode turns the charger around and produces an adjustable 4.55 V to 5.5 V at 1.5 A for an output port, with 22 millisecond start-up. That is the power-bank function: the same inductor and the same switches serve both directions, so the bill of materials does not double. The boost efficiency of 90 percent is measured at 5.1 V, and it falls as the cell voltage falls, which is why the usable output current at a nearly empty cell is lower than the headline.

Plus or minus 0.5 percent on charge voltage is 21 mV on a 4.2 V cell, and that margin is what keeps a cell inside its specified window over life. Charge current accuracy of 7 percent is loose by comparison and is fine because the current sets charge time, not cell health. Reading the two numbers as one accuracy figure is the usual mistake when comparing chargers.

Twenty microamp of battery leakage in shipping mode is what keeps a product on a warehouse shelf from arriving flat. Over a year that is 175 mAh, a tenth of a phone cell, so a product that ships with a half-charged battery still has charge when it is unboxed. The mode has to be entered deliberately, and it is the last register write before the product is packed.

Every limit on this part is a register value, and the register default at power-up is what the product does before the host wakes up. A device that boots with a 3 A input limit on a 500 mA port will collapse the port during the boot window, before any firmware has had a chance to lower it. The safe default is the lowest limit the product can work with, raised later once the source has been identified, and that order of operations belongs in the bring-up notes rather than in the driver.

Where this order code fits

It fits a power bank, a tablet, a portable speaker or an internet-of-things device that charges from USB and has to be able to act as a USB source itself. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the boost output available while the charger is charging? No. Charge and boost are separate states, and the mode register selects one. A product that needs to charge and supply at the same time is a different topology with two converters.

How is the input current limit chosen? By the host over I2C after it knows what the source can supply, with the maximum power tracking loop as the fallback when the source is weaker than the register says. Both have to be configured, not one.

Why is the charge current tolerance so much wider than the voltage tolerance? Because the current sets charge time and the voltage sets cell health. A 7 percent current error changes how long a charge takes; a 7 percent voltage error would overcharge the cell, which is why the voltage loop is trimmed to half a percent.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.