BQ24196RGER
Product Specifications
BQ24196RGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24196RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24196RGER: single cell 2.5 A I2C charger with narrow VDC power path and 5 V boost
BQ24196RGER is a single cell switch mode charger with narrow VDC power path management in a VQFN body of 24 pins. The part charges from a 3.9 V to 17 V adapter or USB source at up to 2.5 A, keeps the system rail at the cell voltage or at a programmable minimum while the cell is deeply discharged, and turns the same inductor around to make 5 V at 1.3 A for a USB OTG port.
Order code and package
| Order code | BQ24196RGER |
| Package | VQFN, 24 pins, 4.00 mm by 4.00 mm |
| Input voltage, operating | 3.9 V to 17 V |
| Charge current | 2.5 A maximum |
| Switching frequency | 1.5 MHz |
| Battery discharge path | 12 milliohm BATFET, up to 9 A |
| USB OTG output | 5 V at 1.3 A, synchronous boost |
| Host interface | I2C, with autonomous fallback |
Electrical parameters that decide the application
| Charge voltage accuracy | plus or minus 0.5 percent at 4.208 V |
| Charge current accuracy | plus or minus 7 percent at 1792 mA |
| Input current accuracy | plus or minus 7.5 percent |
| Boost output accuracy | plus or minus 2 percent |
| Charge efficiency | 92 percent at 2 A |
| Boost efficiency | 93 percent at 1 A |
| Input current limit rungs | 100, 150, 500, 900, 1200, 1500, 2000, 3000 mA |
| Precharge to fast charge | 2.8 to 3.0 V rising, 2.6 to 2.8 V falling |
| Recharge threshold | 100 mV below the regulation voltage |
| BATFET on resistance | 15 milliohm typical |
Points to check before this part goes on a BOM
The default charge voltage is 4.208 V, not 4.20 V, and the host has to write the register before the first charge. At 0.5 percent regulation accuracy the top of the window from that default is 4.229 V, so a cell specified at 4.20 V plus or minus 1 percent is already outside the part as it powers up, before any host code runs.
The input current limit is a fixed ladder of 100, 150, 500, 900, 1200, 1500, 2000 and 3000 mA with 7.5 percent accuracy, so the 500 mA USB 2.0 rung can draw 537 mA and the 900 mA USB 3.0 rung can draw 967 mA. There is no 450 mA or 850 mA rung to absorb the tolerance, so a product that must stay inside a host port contract needs the rung below or an external limiter.
2.5 A into 4.2 V is 10.5 W and 92 percent efficiency means 11.4 W in, so 0.91 W is shed in a 4 by 4 mm body. That input is 2.28 A at 5 V, which is above the 2 A rung and inside the 3 A rung, so the adapter and cable must be chosen for the rung rather than for the charge current in the specification.
The battery FET is 12 milliohm and is quoted for up to 9 A of discharge; 9 A squared times 0.012 ohm is 0.97 W inside the same package, on top of the charger loss. A handheld that pulls 9 A in burst from the cell is asking the die to shed about a watt through the exposed pad, so the copper under the package is part of the current rating and not a mechanical detail.
OTG makes 5 V at 1.3 A, or 6.5 W, from a cell that may be at 3.5 V. At 93 percent boost efficiency that is 7.0 W from the battery, which is 2.0 A of cell current at 3.5 V, twice the 1 A at which the 93 percent figure was measured, and a cell near its cutoff cannot support the headline OTG current at all.
Precharge runs from about 2.6 V to 3.0 V and its accuracy is 20 percent, the widest tolerance in the part. A 2.5 A charger set to a 10 percent precharge delivers between 200 mA and 300 mA depending on the unit, so a cell datasheet that limits precharge to 0.1 C needs the register set below the limit rather than at it.
Recharge sits 100 mV below the regulation voltage, which is 4.108 V at the 4.208 V default. A host that re-enables charge on its own comparator at 4.15 V will fight this one, cycle the safety timer and keep the cell between 4.15 V and 4.21 V indefinitely, which is the opposite of what a long shelf life needs.
The minimum system voltage is programmable and the power path holds the rail there while the cell is in precharge, so a 3.5 V system floor means the regulator supplies 3.5 V from a cell at 2.7 V. That boost path is the reason instant-on works with no battery, and it is also why the input current is higher than the charge current during a cold start.
The short circuit detector takes over below about 2.0 V on the cell and holds the current to 200 mA. A pack that has been left flat in storage for a year comes back through that path, and 200 mA into a damaged cell is still enough to heat it, so the cell's own protection board remains the backstop rather than this limit.
With a 1 microhenry inductor at 1.5 MHz the ripple is about 85 mA at the 5 V to 4.2 V operating point, which is 3.4 percent of a 2.5 A charge. The inductor is therefore chosen by saturation current and by its resistance at 2.5 A rather than by ripple, and a part with 50 milliohms of resistance dissipates 0.31 W on the same current.
The part runs in host mode while the host refreshes its registers and falls back to default mode when the traffic stops, so a product whose firmware loop can stall for longer than the watchdog period will silently revert to the 4.208 V default and the default current ladder. The watchdog period has to be checked against the slowest path in the firmware, not against the typical loop time.
Where this order code fits
Handheld instruments, portable speakers, point of sale terminals and single cell products that run from the same 5 V input that charges the cell are where this order code is normally specified. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does the part charge without a host? Yes. With no host traffic it runs its autonomous sequence using the pin strapping and the stored registers, so a product that never brings up the I2C bus still charges, it just uses the default 4.208 V limit and the default current ladder.
What happens with no battery fitted? The narrow VDC path regulates the system at the cell voltage or at the programmable minimum, whichever is higher, so a missing cell does not stop the system; the boost path carries the full system load from the adapter while the charge current reads zero.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.