Contact Us

BQ24165RGER

Brand: Texas Instruments
Texas Instruments BQ24165RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24165RGER — Power Management & Signal Chain | Superb Automation

BQ24165RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24165RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24165: two inputs, 2.5 A, and a power path that keeps the system alive

The BQ24165RGER is a single cell charger with two isolated inputs, one for a USB port and one for a higher power adapter or a wireless power receiver. The IN input has precedence and can deliver up to 2.5 A of charge current. The USB input is limited to 1.5 A. Both inputs are protected separately, at 6.5 V on the USB side and 10.5 V on the IN side, against a 20 V absolute maximum rating.

The power path is the reason the part exists. A separate N-channel MOSFET controller feeds the system rail from the adapter while the pack charges, so a product with a deeply discharged pack, or with no pack at all, still starts and still makes a GSM call. That call is the hard case: a GSM transmitter pulls around 2 A in bursts, and a charger wired straight to the cell would drop the rail on the first burst. Here the system load is fed from the adapter through the path FET, and the pack is charged with whatever current is left.

Key data for the BQ24165RGER

FunctionSingle cell switch mode charger with dual input and power path management
Charge currentUp to 2.5 A from IN, up to 1.5 A from USB, with integrated FETs
Input rating20 V rating, 6.5 V OVP on USB, 10.5 V OVP on IN
Voltage accuracyPlus or minus 0.5 per cent battery regulation
Current accuracyPlus or minus 10 per cent charge current
ProgrammingResistor set charge current, input limit and VINDPM threshold on IN
JEITACE1 and CE2 selector inputs on the bq24165, TS pin for pack temperature
Supply current15 microamps control supply, 5 microamps in the lower state, both typical
Supplement modeSystem draws from the pack when the adapter cannot carry the load
PackagesWCSP and QFN, 20 pin, in reel and cut tape rows

Body and ordering data

Three dies share the datasheet and the body options: bq24165, bq24166 and bq24167. The ordering table prints all twelve rows with the same 6.5 V USB threshold and the same 10.5 V IN threshold, and separates them on the temperature monitor and the JEITA behaviour. The bq24165 uses two selector inputs. The bq24166 carries the standard temperature window on the TS pin. The bq24167 carries the full JEITA profile on the same pin.

The order code on this page is BQ24165RGER, the QFN in a large reel. The RGET row is the same body on a small reel. The YFF rows are the chip scale body. When a second source is quoted against this string, the first thing to compare is the TS pin behaviour rather than the pin count, because the three dies are pin compatible and the difference only shows up in the temperature profile.

The two thresholds that decide field failures

Both overvoltage thresholds are fixed in silicon rather than programmed by a resistor, and they are set for very different sources. The 6.5 V USB window assumes a compliant port that never exceeds 5.5 V. The 10.5 V IN window assumes a 9 V or 12 V adapter with some cable drop and some ringing on plug in.

A product that feeds a 12 V adapter into the USB pin will trip the 6.5 V protection on every insertion, and the unit will look dead to the user while the protection is doing exactly what it was built to do. The reverse mistake, feeding a 5 V port into IN, leaves the product unprotected against a faulty adapter up to 10.5 V. Both mistakes are common on boards where the two connectors look interchangeable.

Where it fits in a build

Handheld terminals, portable media players, netbooks and any product that has both a USB service port and a barrel jack adapter. The medical handheld case is a good fit when the pack has to be replaceable and the unit must start on the adapter alone. The medical device components page covers the traceability and date code questions that come with that market.

For a product that charges from USB only, the second input is dead weight and a single input part costs less and takes fewer pins. For a product that charges from a wireless receiver plus USB, the dual input is the whole point, and the precedence rule on IN is what keeps the receiver from fighting the cable.

The sourcing side of this part is covered on the pin to pin cross reference. When a platform has to carry both the QFN and the chip scale rows under one approval, that page covers the pin and thermal checks we run before calling them equivalent.

Questions we get on this code

Does the 2.5 A apply with both inputs connected? No. The IN input takes precedence, and the USB input is isolated while IN is valid. The 2.5 A figure is the IN path.

What happens when the adapter cannot carry the system load? The part enters supplement mode and the pack makes up the difference, which is why the system stays up during a transmit burst.

Is the QFN row the same die as the WCSP row? Yes, and the electrical table is shared. What changes is the thermal path. The QFN spreads heat into the board, and the chip scale body relies on the copper under it, so the 2.5 A figure needs checking against the actual copper area on each body.

How do I tell the 165 from the 167 on a reel? By the order code, not by the marking alone. The three dies share one marking family, and the only safe check is the code on the reel label against the addendum row.