Contact Us

BQ24072TRGTR

Brand: Texas Instruments
Texas Instruments BQ24072TRGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24072TRGTR — Power Management & Signal Chain | Superb Automation

BQ24072TRGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24072TRGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24072TRGTR: single cell 1.5 A linear charger with power path in a sixteen pin VQFN

BQ24072TRGTR is a standalone linear charger and power path device that runs a system rail and the cell from the same input at the same time in a VQFN body of 16 pins. The part takes a USB port or a wall adapter up to the overvoltage trip and charges at up to 1.5 A from an external resistor. The power path is the feature that matters on a product with a display or a radio, because the system rail stays alive while the cell is deeply discharged and takes current from the adapter first. The RGT body is 3.00 mm by 3.00 mm, so it fits under a connector on a small board.

Order code and package

BQ24072RGTRVQFN RGT, 16 pins, 3000 pieces on a large reel, NIPDAU, Level-2-260C-1 YEAR, marking CKP
BQ24072RGTR .A and .Blabel rows of the same body and the same 3000 piece reel, same NIPDAU finish
BQ24072RGTRG4the green row, same body and reel, printed separately in the addendum
Body size3.00 mm by 3.00 mm, sixteen pins, thermal pad underneath
Temperatureminus 40 to plus 85 C operating free air on every published row
Certificationthe BQ24072 row carries IEC 62368-1, and the BQ24074 member carries the functional safety documentation

Electrical parameters that decide the application

Input rangeup to 28 V at the IN pin, with the overvoltage trip at 6.4 to 6.8 V on this member, 6.6 V typical
Charge voltage4.16 V to 4.23 V window, 4.20 V typical, held over the full temperature range
Fast charge current25 mA to 1500 mA, set by a resistor from ISET to VSS between 590 ohm and 8.9 kohm
Charge current factorKISET 797 to 975 Aohm, 890 Aohm typical, so a 1 kohm resistor gives about 890 mA
Precharge currentset by the same resistor through KPRECHG of 70 to 106 Aohm, 88 Aohm typical
Precharge thresholdVLOWV 2.9 V to 3.1 V, 3.0 V typical, with 25 ms of deglitch in each direction
Terminationinternally set at 10 per cent of the fast charge current, 9 to 11 per cent over temperature, 25 ms deglitch
Recharge100 mV below the regulation voltage, 62.5 ms deglitch, so a load pulse does not restart the cycle
Safety timer18000 s typical with a 48 kohm resistor, equal to ten times RTMR times KTMR of 36 to 60 s per kohm
Sleep current6.5 uA maximum into the BAT pin with the input absent, 4.3 uA typical
Standby current50 uA maximum into IN with the charger idle, active supply 1.5 mA maximum

Family variants and how they differ

BQ24072 against BQ24073the 73 regulates the system rail at a fixed 4.4 V while the 72 tracks the cell at 225 mV above it
BQ24074 against the restthe 74 raises the overvoltage trip to 10.5 V and adds the external termination resistor on ITERM
BQ24075 against BQ24072the 75 holds the rail at 5.5 V for a boost stage downstream and adds the SYSOFF input
BQ24078 and BQ24079the 78 regulates the cell at 4.35 V and the 79 at 4.1 V, both keeping the tracking rail of the 72
DPPM against VIN-DPMthe DPPM loop lowers the charge current when the system rail sags, and VIN-DPM stops the input from collapsing on a weak source
TS methodthis member compares the thermistor voltage against fixed windows rather than running a current source through it

Points to check before this part goes on a BOM

The ISET resistor sets two currents at once. The fast charge current and the precharge current come from the same pin through two different factors, and the termination current is a fixed fraction of the fast charge current. A build that raises the fast charge current therefore raises the termination current with it, which is how a 1.5 A build ends a cycle at 150 mA and leaves a pack at about 90 per cent of its real capacity.

The tracking rail is not a regulator. On this member the system output sits 225 mV above the cell, so when the cell is at 3.0 V the rail is at 3.2 V. A downstream 3.3 V regulator with a 300 mV dropout will fall out of regulation in that window, and the product browns out before the charger has done anything wrong. Members with a fixed 4.4 V or 5.5 V rail exist for exactly this case.

A 6.6 V trip is a USB trip, not an adapter trip. The overvoltage window protects against a wrong wall adapter plugged into the same connector, and the recovery has 110 mV of hysteresis with a 50 us blanking time. A source that sits right at the trip point will oscillate between charge and no charge rather than fail cleanly, and the symptom is a charger that works on one bench supply and not on another.

The safety timer is a backstop and it can end a real cycle. 18000 s is five hours, and a cell that is charged from a deeply discharged state at a low input current can run past it. When the timer expires the part stops and waits for a recharge event, so a product that reports a pack that never reaches full is often a timer that needs to be programmed from the adapter current rather than from a fixed resistor.

Sleep current is the number that decides shelf life. 6.5 uA maximum into the cell with the adapter removed is what a product with no load draws in storage. On a 2000 mAh cell that is about 0.3 per cent a month, which is acceptable, but only if the system rail really is off, because the path from IN to OUT is not the only leakage in a portable product.

The package has a thermal pad and it must be soldered. At 1.5 A from a 5 V input into a 3.6 V cell the part dissipates more than 2 W, and the sixteen pin body cannot move that heat through the leads alone. A pad with four vias into a ground plane is the difference between a charger that runs at 125 C and one that folds back the current on every charge.

Where the board goes wrong

The input capacitor is the part that decides whether the overvoltage trip fires cleanly. A 1 uF part at the connector with a long trace to the IN pin lets a hot plug spike reach the die, and the part trips or survives depending on the cable. The vendor land pattern puts the capacitor within a few millimetres of the pin for that reason.

The second fault is a system load that draws more than the input limit while the cell is also charging. The DPPM loop then holds the rail at the reduced level permanently, the charge current never reaches its programmed value, and the product looks like a charger that is undersized rather than a load that is too large.

What to ask a supplier for

Ask for the reel size and the finish with the order code. This body is published at Level 2 with a one year floor life, which means a reel opened on a bench and left for a season needs a bake before reflow, and the label is the only record of when it was opened.

Ask also which revision the reel carries. The family has been through several revisions, and the charge current range and the termination behaviour moved between them, so a build that was qualified on an older reel should be rechecked against the current document before a second run.

Where this order code fits

Handheld instruments, asset trackers, doorbell cameras and portable medical devices use this class of part because the product has a radio or a display that must run while the cell is charging. The tracking rail also matters in a product that ships with the cell at 30 per cent state of charge and has to boot on the bench before the cell is connected. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can the system run with the cell removed? Yes on this member, because the power path feeds the system rail from the input independently of the cell. The rail then sits at the DPPM threshold or at the input minus the drop, and the part reports the condition on the PGOOD and CHG pins rather than shutting down.

Why does the charge current fall when the input sags? Because the DPPM loop compares the system rail with a threshold 100 mV below its regulation point and reduces the charge current to hold it. That is the intended behaviour on a weak source such as a long USB cable, and the current recovers as soon as the rail comes back.

Does the part stop charging at 4.2 V exactly? It holds 4.16 to 4.23 V over temperature and terminates when the current falls to 10 per cent of the programmed value. The cell then relaxes and the part restarts when the voltage falls 100 mV, so a pack on a charger spends most of its life between those two points rather than at the regulation voltage.

What happens if the thermistor is missing? The TS pin has a fixed window and an unconnected pin reads outside it, so the charger refuses to start. The usual fix is a 10 kohm resistor to ground where the pack has no thermistor, and the value has to match the window of this member rather than a value copied from another family.

Is the ISET pin a current monitor? The voltage at ISET reflects the actual charge current while charging, so a host ADC can read it. It is not a separate monitor output and it does not stay proportional when the part is in precharge or in a DPPM limit, which is where a naive reading misleads.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.