BQ2057WTSTR
Product Specifications
BQ2057WTSTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ2057WTSTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ2057WTSTR: an 8.4 V linear charger in an eight pin TSSOP
BQ2057WTSTR is the 8.4 V member of the BQ2057 family of linear charge management ICs for single and two cell lithium ion and lithium polymer packs, in the eight pin TSSOP body on a tape and reel. It regulates voltage to better than one percent, terminates on a minimum current, restarts on a pack voltage drop, watches the pack thermistor before and during charge, and does all of that with an external pass transistor and a handful of resistors.
The family is four fixed voltages on one die: 4.1 V, 4.2 V, 8.2 V and 8.4 V. The letter in the middle of the code picks the voltage, and the package letters pick the body. This order code is the W, which is 8.4 V, in the TS body, which is the TSSOP, with the R on the end for tape and reel. Getting the letter wrong is the most expensive mistake on this family, because 8.2 V and 8.4 V parts are pin identical and only a pack that is charged to the lower voltage for a season shows the difference.
The figures below come from SLUS025G, revised December 2022, and from the orderable addendum in the same document. They are the ones we check against a customer pack specification before quoting, because a two cell charger is specified by the pack, not by the IC, and the pack supplier, the protection board and the charger all have to agree on the same regulation voltage before anybody builds anything.
8.2 V or 8.4 V: the letter that decides a pack
A two cell lithium ion pack is 8.4 V at full charge when each cell is 4.2 V, and 8.2 V when each cell is 4.1 V. Both chemistries are sold, both are called lithium ion on the purchase order, and the difference is in the cathode blend and the electrolyte rather than in the shape. Charging a 4.1 V cell to 8.4 V costs cycle life and, in a sealed product, can cost the pack, and charging a 4.2 V cell to 8.2 V leaves roughly 8 percent of the capacity unused.
The BQ2057T is the 8.2 V part and the BQ2057W is the 8.4 V part. They share the pinout, the current loop and the thermistor window, so a board built with one works with the other and only the end of charge voltage changes. That is convenient for a platform that serves two pack suppliers, and it is dangerous for a production line that has both reels open at once, which is why the marking on the body is worth reading at incoming rather than trusting the reel label alone.
The single cell versions are the same story one cell down: the plain BQ2057 is 4.1 V and the BQ2057C is 4.2 V. A product that moves from a single cell to a two cell pack keeps the circuit topology and changes the letter, the pass transistor rating and the thermistor divider.
The numbers a charger quotation turns on
| Function | Linear charge management IC for one or two lithium ion or lithium polymer cells |
| Regulation voltage | 8.4 V nominal for this order code, 8.317 V minimum, 8.484 V maximum |
| Regulation accuracy | Better than plus or minus 1 percent over temperature and supply |
| Charge phases | Conditioning, constant current, constant voltage, then termination |
| Sense threshold, high side | 125 mV typical, 103.6 mV minimum, 143 mV maximum |
| Sense threshold, low side | 130 mV typical, 108.1 mV minimum |
| Precharge threshold | 6.30 V typical, 6.18 V minimum, 6.43 V maximum for this code |
| Precharge current | 13 mV typical across the sense resistor, 22 mV maximum |
| Termination threshold | minus 14 mV typical across the sense resistor |
| Recharge threshold | 200 mV below the regulation voltage, 196 to 204 mV |
| Thermistor window | 30 percent of VCC lower limit, 60 percent of VCC upper limit |
| AutoComp gain | 2.4 V per V typical in the low side dual cell path, 2.09 to 2.76 |
| Dropout voltage | 0.3 V, which sets the minimum input headroom |
| Charge status output | STAT pin, single or dual LED, or a host processor input |
| Sleep mode | Automatic low power state when VCC is removed |
| Package | TSSOP, PW, 8 pins, 4.40 mm by 3.00 mm body |
| Ambient range | minus 20 to plus 70 degrees Celsius |
| Carrier | Tape and reel, 2000 pieces, part marking 2057W |
| Moisture level | Level 2, 260 degrees, one year floor life |
125 mV of sense voltage and the resistor that follows
Charge current is set by a resistor between the supply and the SNS pin, or between the pack negative and the SNS pin, depending on whether the sense element sits on the high side or the low side. The loop holds 125 mV across that resistor at the high side setting, so a 1 A charge current needs 125 milliohm and dissipates 125 mW. At 2 A the resistor is 62.5 milliohm and dissipates 250 mW, and at that point the resistor is a 2512 body rather than an 0805, which is the sort of detail that turns up late in a board review.
The tolerance on the current is the tolerance on the sense threshold, not the tolerance on the resistor. The window is 103.6 mV to 143 mV, which is about minus 17 percent to plus 14 percent around the 125 mV typical, so two boards built from the same BOM can charge at 0.83 A and 1.14 A respectively when the target is 1 A. For a product that quotes a charge time, that spread has to be in the number, and the resistor tolerance, usually 1 percent, is the smaller part of the error.
The low side option exists because the sense resistor then sits at the pack negative, which is convenient when the pass transistor is a PNP on the high side and the supply is shared with the rest of the product. The trip point moves from 125 mV to 130 mV in that configuration, which is a small change and a different board arrangement. The choice is a topology decision, and it is made with the pass element, not after it.
Precharge at 6.3 V and the thermistor window
A two cell pack that has been sitting empty comes up below 6.30 V, and the part will not apply the full current at that voltage. It applies the conditioning current, which is set by 13 mV across the same sense resistor, roughly a tenth of the regulation current, until the pack passes the threshold. That is what keeps a deeply discharged pack from being charged at 1 A and what keeps the pass transistor from dissipating the whole input voltage across itself.
The thermistor window is the other interlock. The TS pin expects a divider that sits at 30 percent of VCC at the lower temperature limit and 60 percent at the upper limit, which with a 10 k negative coefficient thermistor and a 10 k series resistor lands on the usual 0 to 45 degree charge window. Outside that window the part inhibits charge and keeps the status output in the state that tells the host why. A product that charges only indoors can widen the window with different resistors, and a product that ships to a cold climate should, because a pack at minus 5 degrees that is refused a charge looks like a broken charger to the user.
The AutoComp function adds a second use for the same thermistor path: it measures the pack impedance rise during charge and raises the output voltage by up to 2.4 V per volt of compensation in the dual cell low side configuration, which shortens the constant voltage phase on a pack with a high internal resistance. It is the feature that separates this family from a plain linear charger, and it is also the feature that has to be disabled or trimmed when the pack supplier changes the cell, because the compensation is tuned to a pack, not to a chemistry in general.
The 70 degree window and what it means for a product
The ambient range for this family is minus 20 to plus 70 degrees, which is narrower than most of the parts on this site and is a real constraint in a sealed enclosure. A charger that sits next to a 45 W load in a plastic box can see 55 degrees ambient on a warm day, and a linear charger at 1 A with 2 V of headroom is dissipating 2 W inside that box, so the case temperature rises another 20 to 30 degrees depending on copper. The part has no junction temperature specification in the electrical table, so the board has to be checked against the ambient rating with the dissipation already counted.
For a product that charges at 500 mA the arithmetic is comfortable. For one that charges at 1.5 A from a 12 V adapter into an 8.4 V pack, the dissipation is 5.4 W and no eight pin body survives that without a thermal path. That is a switch mode charger question, not a BQ2057 question, and we say so before a quotation rather than after a failed thermal test.
Ordering, marking and the inspection that matters
This order code is the TSSOP body, 2000 pieces on a reel, moisture level 2 with a one year floor life at 260 degrees, marking 2057W. The MSOP body exists for the single cell versions only, and its pinout differs, so a board that was laid out for the MSOP cannot take the TSSOP without a change. The tape and reel orientation follows the standard quadrant for an eight pin body, and the pin one mark is a dot rather than a chamfer on this package.
Because the four voltage versions are pin identical, our incoming check reads the marking and the date code on every reel of this family and records the voltage code against the customer part number. That check is in our component traceability report, and it exists because a mixed reel of 8.2 V and 8.4 V parts is invisible until a pack comes back.
Where this part fits in a sourcing plan
The BQ2057 family has been in production since 2001 and has been revised as recently as December 2022, which makes it one of the more stable linear chargers in the catalogue and also one of the more counterfeited, because the price of the genuine part is high enough for a remark to look attractive. We source this order code through franchised channels only and can compare it against the pin compatible alternatives in our power management cross reference when a customer needs a second source.
For a product that is moving away from this family, the same cross reference page lists the switch mode alternatives that fit the same board area, and our obsolete part cross reference hub carries the parts that have already gone end of life. The BQ2057 itself is active in every voltage version as of the current addendum, so the decision is a thermal one rather than a supply one.