ADS62P45
Product Specifications
ADS62P45
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADS62P45 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADS62P45: dual 14 bit 125 MSPS converter, the fastest member of the ADS62P4X family
ADS62P45 is the 125 MSPS top of the dual 14 bit family, with the same digital block and the same 64 pin body as the slower members in a QFN body of 64 pins. The ADS62P45 is the 125 MSPS member of the dual 14 bit family and the top of that range. It keeps the digital processing block of its siblings, with offset correction, fine gain in 0.05 dB steps, decimation by 2, 4 or 8 and 24 tap filters, and it puts both channels out on DDR LVDS or parallel CMOS. Analog power rises to 799 mW at the top rate, and the family table gives 88 dB of SNR at a 10 MHz input for this rate.
Order code and package
| Order code | ADS62P45 |
| Channels | two, simultaneous |
| Resolution | 14 bit |
| Maximum sample rate | 125 MSPS |
| Family position | fastest of four, 125, 105, 80 and 65 MSPS |
| Digital block | offset correction, fine gain, decimation, 24 tap filters |
| Decimation | by 2, 4 or 8 |
| Output interface | DDR LVDS or parallel CMOS |
| Package | 64 pin QFN, 9 mm by 9 mm |
| Analog power | 799 mW at 125 MSPS |
| Crosstalk | 95 dB |
| Document | SLAS561C, July 2007, revised February 2012 |
Electrical parameters that decide the application
| SNR at a 10 MHz input | 88 dB, from the family table at this rate |
| Power per sample pair | 6.4 nJ at 125 MSPS |
| Data rate | 3.5 Gbps per channel at full rate, 14 bit |
| Coarse gain | 3.5 dB |
| Fine gain | up to 6 dB in 0.05 dB steps |
| Filter length | 24 taps |
| Input range | 2 V peak to peak differential |
| Clock amplitude | 400 mV peak to peak minimum |
| Decimated rates | 62.5, 31.25 and 15.625 MSPS |
| Temperature | minus 40 to 85 C |
| Reference | internal or external |
| Package sharing | same body as the 105, 80 and 65 MSPS members |
Points to check before this part goes on a BOM
This is the member where the SNR costs the most. The family table gives 88 dB at 125 MSPS against 92 dB at 105 MSPS and 94 dB at 65 MSPS, so the fastest rate gives up 6 dB of dynamic range against the slowest. A link budget that was written on the 65 MSPS number and then moved to this part loses that 6 dB, which is more than a typical blocker margin.
799 mW of analog power at the top rate is the highest in the family, and it is still inside the same 9 mm body. The board that hosts the 65 MSPS member can host this one thermally, which is what makes the rate upgrade a part change rather than a board change. The clock and the decimation setting are the two things that must move with it.
At 125 MSPS and 14 bit each channel is 3.5 Gbps, and decimation is the practical answer for a capture device that cannot take that. Decimation by 2 gives 62.5 MSPS, which halves the interface rate while keeping the full analog bandwidth, and the on chip filter handles the alias rejection.
88 dB of SNR at 125 MSPS only means something if the clock is good enough. At this rate the aperture jitter that costs a bit is well under a picosecond, so the clock source and its distribution are part of the dynamic range, and a board that keeps the same clock as the 65 MSPS build usually measures worse than the data sheet.
The 24 tap filter and the decimation setting are programmable per channel, so the two channels can run different responses. That is useful in a dual band receiver and dangerous in a phase coherent pair, where any difference between the two filter responses appears as a phase or amplitude error at the band edge.
Coarse and fine gain together give up to 9.5 dB of range in front of the converter, and the reason to use it is SFDR at a reduced input level rather than headroom for a larger signal. Turning gain up does not extend the input range; it moves the full scale down.
For repair work this is the part most often asked for, because it is the top of the family and the first to tighten. The body and the pin out are shared with three slower members, so a build that only needs 80 MSPS can be served from a different order code in the same socket while the 125 MSPS line is short.
Power is quoted for the analog section, and the digital block that carries the filters and the decimation adds to it. A build that enables the custom 24 tap filter therefore draws more than one that passes the raw stream, so the thermal check has to be run with the filter loaded rather than on a default configuration.
Where this order code fits
This order code belongs on wideband cellular receive paths with multiple carriers, radar digitisation, test and measurement instruments and satellite receivers where 125 MSPS of instantaneous bandwidth per channel is required. It is also the upgrade path for a board already carrying the 105 MSPS member, since the body and the pin out do not change. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can an 80 MSPS build use a part from this family in the same socket? Yes, the package and the pin out are shared, and the slower members use less analog power. The register settings for the digital block are the same across the family.
Why is the SNR lower at the higher rate? The converter runs faster and the noise bandwidth grows with it. The family table shows 88 dB here against 94 dB at the 65 MSPS member.
Is decimation needed? Only if the capture device cannot take 3.5 Gbps per channel. It reduces the interface rate and provides alias rejection at the same time.
SUPERB quotes this order code with packing and date codes stated on the offer, and the BOM Shortage Recovery page sets out the checks that keep a rate upgrade from turning into a re-qualification.