Contact Us

ADS62P44

Brand: Texas Instruments
Texas Instruments ADS62P44 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS62P44 — Power Management & Signal Chain | Superb Automation

ADS62P44

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS62P44 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS62P44: dual 14 bit 105 MSPS converter with decimation filters in a 64 pin QFN

ADS62P44 is a two channel 14 bit converter that samples at 105 MSPS, carries a digital processing block with decimation by 2, 4 or 8 and programmable 24 tap filters, and puts both channels out on one bus in a QFN body of 64 pins. The ADS62P44 is the 105 MSPS member of the dual 14 bit family that runs from 65 to 125 MSPS. Both channels sample together into a 64 pin QFN body, and the digital block behind them offers offset correction, fine gain in 0.05 dB steps, decimation by 2, 4 or 8 and built in or user programmed 24 tap filters. Analog power is 710 mW at 105 MSPS and crosstalk between the channels is 95 dB.

Order code and package

Order codeADS62P44
Channelstwo, simultaneous
Resolution14 bit, no missing codes
Maximum sample rate105 MSPS
Family rates125, 105, 80 and 65 MSPS across the four members
Digital blockoffset correction, fine gain, decimation and 24 tap filters
Decimationby 2, 4 or 8
Output interfaceDDR LVDS or parallel CMOS
Package64 pin QFN, 9 mm by 9 mm
Analog power710 mW at 105 MSPS
Crosstalk95 dB
DocumentSLAS561C, July 2007, revised February 2012

Electrical parameters that decide the application

SNR at a 10 MHz input92 dB, from the family table at this rate
Coarse gain3.5 dB
Fine gainup to 6 dB in 0.05 dB steps
Offset correctionon chip, per channel
Filter length24 taps, built in or user programmed
Input range2 V peak to peak differential
Clock amplitudedown to 400 mV peak to peak
Power per sample pair6.8 nJ at 105 MSPS
Data rate at full rate2.94 Gbps per channel before decimation
Decimated rate52.5, 26.25 or 13.125 MSPS for decimation of 2, 4 or 8
Temperatureminus 40 to 85 C
Referenceinternal, external option

Points to check before this part goes on a BOM

Decimation is the feature that changes the system, not just the converter. At 105 MSPS with decimation by 4 the output is 26.25 MSPS, which a small FPGA can capture without an external digital down converter, and the on chip filter does the anti alias work that would otherwise be a line of fabric. The trade is that the wanted band has to fit inside the decimated Nyquist zone, which is a system planning item rather than a register setting.

The SNR of 92 dB at a 10 MHz input belongs to this rate in the family table, and the table gets better as the rate falls. A specification that quotes the 65 MSPS member's 94 dB for a 105 MSPS build is quoting the wrong column, and the difference of 2 dB is exactly the kind of margin a link budget cannot afford to lose.

The 24 tap filter is programmable, which means the filter response is part of the product definition. A build that uses the built in low pass response and a build that loads a custom band pass response from firmware behave differently at the band edges, and the two cannot be compared on the bench without knowing which response was loaded.

Coarse gain of 3.5 dB and fine gain of up to 6 dB in 0.05 dB steps exist to trade SNR for SFDR. The fine step is small enough to match the two channels, which matters for an I and Q pair where a gain difference of a tenth of a dB already shows as image rejection. The gain is a register setting and it has to be identical on both channels to keep the match.

Crosstalk of 95 dB between the two channels is what makes the part usable for a phase coherent pair. It also means a strong signal in one channel leaks about 18 uV into the other at a 1 V input, which is a level worth knowing when the second channel is watching a return that is 80 dB down.

Analog power of 710 mW at 105 MSPS is 6.8 nJ for the pair of samples. The digital block adds to that and it is not free: a build that enables decimation and the custom filter draws more than a build that passes the raw stream through, so the thermal budget has to be checked with the filter enabled.

The 64 pin 9 mm body is shared across the four rates, so the same board can carry the 125 MSPS member later. What changes is the clock and the power, and both are within the same thermal envelope at the top of the range, which is why the family is often selected by the clock source rather than by the converter.

Where this order code fits

This order code belongs on multi channel receive paths for cellular infrastructure, on ultrasound and medical imaging front ends that need two matched channels, and on radar and instrumentation digitisers where a decimation stage before the FPGA saves fabric. The on chip filter is often what makes a lower rate FPGA feasible without an external digital down converter. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the on chip filter remove the need for an external digital down converter? For decimation by 2, 4 or 8 with a band that fits the decimated zone, yes. The filter replaces the first stage and the FPGA only has to capture the reduced rate.

Are the two channels matched well enough for I and Q? They sit on one die with 95 dB of isolation, and the fine gain step is 0.05 dB. The remaining mismatch is in the analog network in front of the part.

Which SNR figure applies to this order code? The 105 MSPS column, which the family table gives as 92 dB at a 10 MHz input. The 94 dB figure belongs to the 65 MSPS member.

SUPERB holds this order code against the exact ordering string with date codes and packing, and the One Stop BOM Sourcing page covers how to keep a dual channel socket supplied when the original line tightens.