Contact Us

ADS6123

Brand: Texas Instruments
Texas Instruments ADS6123 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS6123 — Power Management & Signal Chain | Superb Automation

ADS6123

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS6123 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS6123: single channel 12 bit 80 MSPS converter in a 32 pin QFN

ADS6123 is the 80 MSPS member of the single channel 12 bit family, in the same 5 mm body as the 65 MSPS part with 318 mW at the higher rate in a QFN body of 32 pins. The ADS6123 samples one channel to 12 bit at 80 MSPS in a 32 pin QFN body of 5 mm by 5 mm, dissipating 318 mW against the 285 mW of the 65 MSPS member. The document covers four rates up to 125 MSPS, offers DDR LVDS or parallel CMOS outputs, and provides coarse and fine gain over a three wire serial interface. The family table gives 93 dB of SNR at a 10 MHz input for this rate.

Order code and package

Order codeADS6123
Channelsone
Resolution12 bit
Maximum sample rate80 MSPS
Family rates125, 105, 80 and 65 MSPS
Output interfaceDDR LVDS or parallel CMOS
Package32 pin QFN, 5 mm by 5 mm
Power318 mW at 80 MSPS
Gain control3.5 dB coarse and up to 6 dB fine over a three wire interface
Input range2 V peak to peak differential
Clock amplitudedown to 400 mV peak to peak
DocumentSLAS560A, October 2007, revised March 2008

Electrical parameters that decide the application

SNR at a 10 MHz input93 dB, from the family table at this rate
Power per sample3.98 nJ at 80 MSPS
Data rate at 12 bit960 Mbps at 80 MSPS
Quantisation floorabout 74 dBFS for an ideal 12 bit converter
Coarse gain3.5 dB
Fine gainup to 6 dB
Offset correctionon chip
Interfacethree wire serial configuration
Temperatureminus 40 to 85 C
Referenceinternal or external
Board area25 square mm for the body
Package sharingsame body as the 65, 105 and 125 MSPS members

Points to check before this part goes on a BOM

Three dB cheaper in dynamic range than the 65 MSPS member and 22 percent more power, this is the middle of the 12 bit family. The choice between the two is a bandwidth question: if the wanted band fits under 32.5 MHz the slower member gives better SNR for less power, and above that bandwidth this is the entry point.

318 mW in a 5 mm body is 3.98 nJ per sample, and the pad under the body is small. Sixteen channels of this converter is 5.1 W in a small area, so the ground plane and the via pattern under each part decide the junction temperature rather than the ambient.

At 80 MSPS the parallel CMOS option is 12 data lines plus clock at 80 MHz, which is at the edge of what a small FPGA can take on general purpose pins. A capture device with a dedicated parallel bus is fine; a device without one needs the LVDS path, and that is a pin count decision.

The 2 V peak to peak differential input with the 3.5 dB coarse step is the same front end as the rest of the family, so an amplifier stage proven on the 65 MSPS member carries over unchanged. That reuse is the practical reason to stay inside one family when a product line spans several bandwidths.

Gain and offset are loaded at start up over three wires, and a part that is not loaded runs at its default full scale. On a multi channel board a wrong or missing configuration step reads as a channel to channel gain difference, which is expensive to chase on the bench if the configuration path is not instrumented.

With 12 bit resolution the practical floor in a wideband application is about 70 dB, which is where the analog front end stops being the limiting element. A board that needs 80 dB of in band dynamic range belongs on the 14 bit member, and the shared footprint makes that a part change rather than a board change.

For supply continuity this member is often the one that stays available when the 125 MSPS part tightens, because it is the middle of the range and used across many instruments. The socket takes any of the four rates, so the alternative is already on the same footprint.

Eighty MSPS at 12 bit is 960 Mbps, which is close to the point where a parallel CMOS bus stops being comfortable. A capture device with a dedicated parallel port takes it; a device where the port shares pins with other functions usually needs the LVDS path, and that decision changes the pin count on the FPGA side rather than the board.

Where this order code fits

This order code suits industrial and medical channels that need a little more bandwidth than 65 MSPS allows while staying in a 5 mm body: ultrasound receive channels with a modest element count, motor and inverter monitoring, optical time of flight receivers and instrumentation front ends with a 30 MHz band. It is also the natural upgrade from the 65 MSPS member on the same footprint. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does this part fit the same board as the 65 MSPS member? Yes, the 32 pin body and the pin out are shared. The clock has to be raised and the power budget re-checked.

How does the SNR compare with the fastest member? 93 dB here against 90 dB at 125 MSPS. A slower converter integrates less noise, which is why the ranking runs backwards against the sample rate.

Is the CMOS output practical at 80 MSPS? It is 12 data lines plus clock at 80 MHz. That fits a capture device with a parallel bus, and beyond that the LVDS option is the safer choice.

SUPERB supplies this order code with packing and date codes on the offer, and the Pin to Pin Cross Reference page covers how a footprint shared across four rates turns into supply flexibility.