Contact Us

ADS6122

Brand: Texas Instruments
Texas Instruments ADS6122 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS6122 — Power Management & Signal Chain | Superb Automation

ADS6122

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS6122 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS6122: single channel 12 bit 65 MSPS converter in a 32 pin QFN

ADS6122 is the 65 MSPS member of the single channel 12 bit family, sharing the 5 mm body and the 285 mW figure with the 14 bit part in a QFN body of 32 pins. The ADS6122 samples one channel to 12 bit at 65 MSPS in a 32 pin QFN of 5 mm by 5 mm and dissipates 285 mW, the same power as the 14 bit member of the same body. The document covers four rates from 65 to 125 MSPS, offers DDR LVDS or parallel CMOS outputs, and provides coarse and fine gain over a three wire serial interface. The family table gives 95 dB of SNR at a 10 MHz input for this rate.

Order code and package

Order codeADS6122
Channelsone
Resolution12 bit, no missing codes
Maximum sample rate65 MSPS
Family rates125, 105, 80 and 65 MSPS
Output interfaceDDR LVDS or parallel CMOS
Package32 pin QFN, 5 mm by 5 mm
Power285 mW at 65 MSPS
Gain control3.5 dB coarse and up to 6 dB fine, over a three wire interface
Input range2 V peak to peak differential
Clock amplitudedown to 400 mV peak to peak
DocumentSLAS560A, October 2007, revised March 2008

Electrical parameters that decide the application

SNR at a 10 MHz input95 dB, from the family table at this rate
Quantisation floorabout 74 dBFS for an ideal 12 bit converter
Power per sample4.38 nJ at 65 MSPS
Data rate at 12 bit780 Mbps at 65 MSPS
Coarse gain3.5 dB
Fine gainup to 6 dB
Offset correctionon chip
Interfacethree wire serial configuration
Temperatureminus 40 to 85 C
Referenceinternal or external
Package sharingsame body as the 14 bit member
Board area25 square mm for the body

Points to check before this part goes on a BOM

The 95 dB SNR figure for a 12 bit converter looks impossible until the band is taken into account. The ideal 12 bit floor is about 74 dBFS, and the measured number is better because it is quoted in a narrow window at a 10 MHz input rather than over the full Nyquist zone, so the practical floor for a wideband application is closer to 70 dB.

This part shares its 285 mW and its 5 mm body with the 14 bit member, which means the price difference buys resolution and not power or area. On a board with many channels that is the useful property: the thermal and mechanical work is done once and the resolution is chosen per build.

Twelve bits at 65 MSPS is 780 Mbps, which fits a parallel CMOS capture without an LVDS receiver. That makes this member the cheapest entry into the family on the digital side as well, since no serializer or LVDS front end is needed.

Gain and offset are loaded over a three wire interface at start up, so a channel that is not configured runs at its default full scale while its neighbours run at the programmed one. The symptom is a gain offset between channels that looks like an analog fault and is actually a configuration step that was skipped.

The 2 V peak to peak differential input with a 3.5 dB coarse gain step gives a way to bring a small signal up without an extra amplifier stage. In an industrial control loop that is often the difference between one active stage and two, and the trade is the SNR that the gain step costs.

A 12 bit converter in a 5 mm body still needs its own supply decoupling and its own ground return, because the digital outputs switch at 65 MHz and the analog input is a 2 V differential signal. A shared ground with a switching regulator on the same plane shows up as spurs that move with the load, not as noise.

For second source work the important point is that the family shares a body but not a resolution. A 12 bit part substituted into a 14 bit socket changes the word width and the register default, so the capture logic has to be re-checked even though the board does not move.

The register default is not the trimmed state. Gain and offset correction are loaded over the three wire interface at start up, so a board where that load fails runs at the untrimmed full scale and looks like an analog fault. Logging the configuration read back at power up is the cheapest way to tell the two apart.

Where this order code fits

This order code fits cost sensitive receive channels where 12 bit is enough: industrial sensors, motor and power monitoring, hand held instruments with a modest dynamic range requirement, and control loops that need a fast converter but not a precision one. The shared 5 mm body means a board can move to 14 bit without a re-spin. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the 14 bit member be used in this socket? Yes, the body and the pin out are shared. The capture side has to accept a wider word and the register settings have to be reloaded.

Is 12 bit enough for a control loop? At 65 MSPS with 70 dB of practical dynamic range it covers most motor and power control loops. Precision measurement of a small signal next to a large one needs the 14 bit member.

What does the three wire interface configure? Gain, offset correction and the output format. The settings are not retained across a power cycle by pin strap, so the start up sequence matters.

SUPERB quotes this order code with date codes and packing, and the How to Reduce Component Cost page covers the cost side of keeping a 32 pin converter socket filled across a product life.