Contact Us

ADC12SJ1600

Brand: Texas Instruments
Texas Instruments ADC12SJ1600 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADC12SJ1600 — Power Management & Signal Chain | Superb Automation

ADC12SJ1600

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADC12SJ1600 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADC12SJ1600: 12 bit 1.6 GSPS converter with a JESD204B and C serial interface in a 10 mm BGA

ADC12SJ1600 is a multi channel 1.6 GSPS 12 bit converter family that puts the samples on a JESD204B or C serial link instead of a wide parallel bus in a FCBGA body of 144 pins. The ADC12SJ1600 converts one, two or four channels to 12 bit words at 1.6 GSPS and delivers them over a JESD204B or JESD204C serial interface running at up to 17.16 Gbps per lane, using two to eight lanes on the multi channel devices and one to four on the single channel device. The document gives 57.4 dBFS of SNR, 64 dBc of SFDR and 9.1 effective bits at a 100 MHz input, an 80 mV peak to peak differential full scale, and a noise floor of minus 147 dBFS at a minus 20 dBFS input. Power is 477 mW per channel on the quad device, 700 mW per channel on the dual and 1000 mW on the single, in a 144 ball FCBGA of 10 mm by 10 mm.

Order code and package

Order codeADC12SJ1600
Channelsone, two or four depending on the device
Resolution12 bit
Sample rate1.6 GSPS
InterfaceJESD204B and JESD204C serial
Lane rateup to 17.16 Gbps
Lane count2 to 8 on multi channel devices, 1 to 4 on the single
Package144 ball FCBGA, 10 mm by 10 mm
Full scale input80 mV peak to peak differential
Documentvendor data sheet for the ADC12xJ1600 family
Power, quad477 mW per channel
Power, single1000 mW

Electrical parameters that decide the application

SNR at 100 MHz57.4 dBFS
ENOB at 100 MHz9.1 bits
SFDR at 100 MHz64 dBc
Noise floorminus 147 dBFS at a minus 20 dBFS input
Full scale80 mV peak to peak differential
Data rate per channel19.2 Gbps at 1.6 GSPS and 12 bit
Power, dual700 mW per channel
CompatibilityJESD204C transmitter compatible with JESD204B receivers
Reference clockrequired for the SerDes transceivers
Timestampprovided by the device for channel alignment
PackageFCBGA 144, 10 mm by 10 mm
Routingserial lanes, which is the reason for the package choice

Points to check before this part goes on a BOM

The 80 mV peak to peak differential full scale is the number that shapes the whole front end. A converter with an 80 mV range needs about 28 dB less gain in front of it than a 2 V device, so the drive amplifier is often a passive balun and the noise contribution of the analog chain drops with it. It also means the input is more sensitive to coupled noise, which is why the board around the input matters more than the converter choice.

JESD204B and C exist here because 19.2 Gbps per channel cannot leave on a parallel bus. The link spreads that over two to eight lanes, and the trade is that the FPGA needs a compatible SerDes receiver and a link training sequence. A board that changes the FPGA family has to re-verify the link, because the lane rate and the framing are not the same across devices.

Power of 477 mW per channel on the quad device is 0.3 pJ per sample, which is an order of magnitude below the converter classes in this band a decade ago. Four channels at that figure is still 1.9 W in a 10 mm body, so the thermal path is through the ball array and the board beneath it.

The noise floor of minus 147 dBFS at a minus 20 dBFS input is the specification that matters in a receiver looking for a small signal beside a large one. At 57.4 dBFS of SNR the instantaneous dynamic range is set by the noise, not by the 12 bit resolution, and the 64 dBc SFDR says spurs are 6 dB above the noise floor at 100 MHz.

Nine point one effective bits at 100 MHz against a 12 bit resolution is the honest figure. The four lost bits are clock jitter and front end bandwidth, and at 1.6 GSPS the jitter requirement is severe: a 100 fs clock with a 100 MHz input limits the SNR to about 62 dB, so the clock is part of the converter specification and not a separate line item.

The timestamp output is what makes multi channel alignment possible without extra hardware. For a phased array or a multi channel oscilloscope, the channels have to be aligned to a fraction of a sample, and a device that reports its own timing removes a synchronization signal from the board.

For procurement this is a modern part on a fine pitch BGA, so the assembly process, the x-ray inspection and the rework capability all have to exist before the part goes on the board. A programme without that capability should plan for it rather than discover it at first article.

Where this order code fits

This order code belongs on multi channel oscilloscopes and digitisers, phased array radar and satellite communication receivers, and wideband test equipment where several 1.6 GSPS channels have to reach an FPGA without a parallel bus. The serial interface is the reason it exists: 12 bits at 1.6 GSPS is 19.2 Gbps per channel, which cannot be carried on a parallel bus across a board. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

Why is the full scale only 80 mV? A small full scale moves the gain requirement into the analog front end and lets a passive balun drive the input. It also makes the input more sensitive to coupled noise.

Does the serial interface work with a JESD204B FPGA core? The transmitter is stated as compatible with JESD204B receivers even though the device is a JESD204C transmitter, so the link can be run in the older mode.

How much power does a four channel device draw? 477 mW per channel on the quad device, which is about 1.9 W in total for the converter.

SUPERB quotes this order code with packing and date codes, and the Component Lead Time Solutions page covers how a wideband multi channel socket is kept supplied through a long programme.