ADC12SJ1600-Q1
Product Specifications
ADC12SJ1600-Q1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADC12SJ1600-Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADC12SJ1600-Q1: automotive grade release of the 1.6 GSPS 12 bit converter with a JESD204 interface
ADC12SJ1600-Q1 is the automotive qualified version of a 1.6 GSPS 12 bit converter family, aimed at radar and sensor digitisation in a vehicle in a FCBGA body of 144 pins. The ADC12SJ1600-Q1 is the automotive release of the 1.6 GSPS 12 bit converter family. The device keeps the JESD204B and C serial interface at up to 17.16 Gbps per lane, the 80 mV peak to peak differential full scale, the 144 ball 10 mm by 10 mm FCBGA body and the quoted 57.4 dBFS of SNR, 64 dBc of SFDR and 9.1 effective bits at a 100 MHz input, and adds the qualification and documentation trail that an automotive programme requires.
Order code and package
| Order code | ADC12SJ1600-Q1 |
| Qualification | automotive release of the base device, documentation per programme |
| Resolution | 12 bit |
| Sample rate | 1.6 GSPS |
| Channels | one, two or four depending on the device |
| Interface | JESD204B and JESD204C serial, up to 17.16 Gbps per lane |
| Full scale input | 80 mV peak to peak differential |
| Package | 144 ball FCBGA, 10 mm by 10 mm |
| Power, quad | 477 mW per channel |
| Power, dual | 700 mW per channel |
| Noise floor | minus 147 dBFS at a minus 20 dBFS input |
| Base device | ADC12SJ1600 |
Electrical parameters that decide the application
| SNR at 100 MHz | 57.4 dBFS |
| ENOB at 100 MHz | 9.1 bits |
| SFDR at 100 MHz | 64 dBc |
| Data rate per channel | 19.2 Gbps at 1.6 GSPS |
| Full scale | 80 mV peak to peak differential |
| Jitter sensitivity | the clock is part of the dynamic range at this rate |
| Lane count | 2 to 8 on multi channel devices |
| Timestamp | supplied by the device for channel alignment |
| Package | FCBGA 144, 10 mm by 10 mm |
| Power, single | 1000 mW |
| Qualification trail | requested with the order for the programme |
| Temperature | per the automotive grade of the release |
Points to check before this part goes on a BOM
The Q1 release is bought for its qualification trail, not for different converter behaviour. The electrical figures are the same as the base device, so a board proven on the base part can move to the automotive code without a re-spin, provided the temperature grade of the release covers the installation point.
Keeping the differential full scale at 80 mV across both releases matters for a programme that starts on the base device. The front end gain, the balun and the input filter all stay the same, so an automotive variant of a board can reuse the analog chain that was proven in the earlier build.
The serial interface is what makes an automotive multi channel front end practical. A 1.6 GSPS channel at 12 bit is 19.2 Gbps, and carrying that on a parallel bus inside a vehicle harness is not realistic; the JESD204 link turns it into two to eight lanes and puts the pin count where the module can afford it.
9.1 effective bits at 100 MHz and 57.4 dBFS of SNR mean the chain is noise limited rather than spur limited, since SFDR is 64 dBc. In a radar receiver that is the desired order: the noise floor sets the detection range and the spurs sit 6 dB above it, so a strong target does not fold back as a false one.
A 10 mm by 10 mm ball grid array in an automotive module has to survive thermal cycling, and the ball array under the die is the only thermal path for about 0.5 W per channel. The board stack and the copper under the device are part of the qualification, not just the part number.
The device provides a timestamp for channel alignment. In a sensor fusion build where several converters sample the same event, that is what removes a separate synchronization wire and its tolerance, and it also makes the alignment verifiable from the captured data.
For procurement the automotive documentation is requested with the order. A supplier who cannot show the qualification trail for this specific release is not offering the same article, even with the same conversion performance, and the difference only appears at an audit.
The serial link is the part that needs re-verification when the capture device changes. A JESD204C transmitter at 17.16 Gbps per lane can be run in a mode a JESD204B receiver understands, but the lane count, the framing and the link training sequence are set by the pairing, so a new FPGA family means a new link validation rather than a drop in replacement.
The 80 mV full scale puts the input filter close to the ball array. A long trace between the balun and the converter picks up coupled noise that a 2 V input would absorb without visible effect, and at this full scale the same coupling costs real signal to noise ratio.
Where this order code fits
This order code belongs on automotive radar and sensor fusion boards, in vehicle test equipment and in platforms where a 1.6 GSPS capture has to be qualified through an automotive flow. The serial interface keeps the lane count low enough for a sensor module harness, which is what makes a multi channel front end practical away from a central compute box. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.
Questions buyers ask
Is the performance different from the base device? The converter figures are the same. The Q1 release adds the qualification and documentation trail that the programme requires.
Can a board proven on the base part move to this release? Yes, if the analog chain and the serial link are unchanged and the installation point is inside the qualified range. The documents still have to be re-issued for the automotive build.
What has to be checked in assembly? The thermal path through the ball array and the inspection method for a fine pitch BGA. X-ray capability is part of the qualification.
SUPERB sources this release against the programme schedule with traceability kept intact, and the Defense Grade Components page lists the documents an incoming audit should expect.