Contact Us

ADC10DV200

Brand: Texas Instruments
Texas Instruments ADC10DV200 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADC10DV200 — Power Management & Signal Chain | Superb Automation

ADC10DV200

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADC10DV200 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADC10DV200: dual 10 bit 200 MSPS converter in a 60 pin WQFN with LVDS or CMOS output

ADC10DV200 is a two channel 10 bit pipeline converter that samples at 200 MSPS and still runs off a single 3.3 V rail at under half a watt in LVDS mode in a WQFN body of 60 pins. The ADC10DV200 converts two channels to 10 bit words at up to 200 MSPS and offers a parallel LVDS or a parallel CMOS output, so one part covers a high speed serial capture and a wide parallel one. The vendor gives 9.6 effective bits and 59.9 dBFS of SNR at a 70 MHz input, with 82 dBFS of spurious free dynamic range at the same frequency. Power is 450 mW at 200 MSPS in LVDS mode and 280 mW at 170 MSPS in CMOS mode, and the analog input bandwidth is stated as greater than 900 MHz.

Order code and package

Order codeADC10DV200
Channelstwo, simultaneous
Resolution10 bit
Conversion rate200 MSPS
Output interfaceparallel LVDS, or parallel CMOS
Package60 lead WQFN, 9 mm by 9 mm by 0.8 mm, 0.5 mm pitch
Supply3.3 V
Power in LVDS mode450 mW typical at 200 MSPS
Power in CMOS mode280 mW typical at 170 MSPS
Analog input bandwidthgreater than 900 MHz
Full scaledifferential, internal reference
Documentvendor data sheet for the ADC10DV200 family

Electrical parameters that decide the application

ENOB9.6 bits typical at a 70 MHz input
SNR59.9 dBFS typical at a 70 MHz input
SINAD59.9 dBFS typical at a 70 MHz input
SFDR82 dBFS typical at a 70 MHz input
Theoretical floor62 dBFS for an ideal 10 bit converter
Power per sample2.25 nJ at 200 MSPS in LVDS mode
Interface load20 data lines plus clock in CMOS mode
Undersamplingsupported by the 900 MHz input bandwidth
Thermal paththe exposed pad under the 9 mm body
Channel matchingboth channels on one die and one clock
Supply tolerance3.3 V nominal, check the recommended range in the document
Temperatureindustrial range as stated by the vendor

Points to check before this part goes on a BOM

The measured SNR of 59.9 dBFS sits close to the 62 dBFS that an ideal 10 bit converter can reach, so almost nothing is left on the table at 70 MHz. What that means in practice is that the analog front end, not the converter, sets the system noise once the input chain is worse than about 60 dB.

The two power figures belong to two different modes and two different rates. LVDS gives 450 mW at 200 MSPS and CMOS gives 280 mW at 170 MSPS, so a board that compares 280 mW with 450 mW and concludes the CMOS mode is cheaper at full rate is reading two operating points as one. At 200 MSPS the CMOS bus is 20 lines toggling at 200 MHz, which is also an emission question.

Sixty pins at 0.5 mm pitch on a 9 mm body means the exposed pad is the only thermal path and it has to be soldered with a via array. 450 mW is small in absolute terms, but a 0.5 mm pitch part that is reflowed with a poor ground plane under the pad runs hotter than the number suggests, and the drift shows first in the offset.

An input bandwidth above 900 MHz is what allows undersampling. A 10 bit converter used to capture a 500 MHz intermediate frequency directly needs the clock to be clean, not just fast: at 200 MSPS the aperture jitter that costs one bit is about 0.4 ps, so the clock source is part of the converter selection and not a separate line on the BOM.

SFDR of 82 dBFS is 20 dB better than the SNR at the same frequency, which tells you the part is limited by noise rather than by linearity at 70 MHz. In a receiver that must see a weak signal next to a strong one, the useful margin is the difference between the blocker level and the noise floor, and the SFDR figure says the spurs will not be the first thing to appear as the input grows.

Two channels on one die with one clock buffer means the pair can be used for I and Q, provided the analog paths outside the part are matched. Gain and phase mismatch in the transformers and the drive network usually dominates once the part itself is matched.

A last point for repair and second source work: the same 10 bit 200 MSPS class is offered by several vendors with a different output format. The output format, the clock amplitude and the register interface have to be compared before a substitution is claimed, and the comparison belongs on paper before a board is reworked.

Where this order code fits

This order code suits digital oscilloscopes, portable spectrum analysers, ultrasound front ends with a modest channel count, radar pulse capture and industrial imaging where 10 bit is enough and 200 MSPS of instantaneous bandwidth is the point. The 900 MHz input bandwidth also lets a board undersample a higher intermediate frequency instead of adding a second mixer stage. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can this part run at 170 MSPS in LVDS mode and keep the same power figure? The published 280 mW belongs to CMOS mode at 170 MSPS and the 450 mW belongs to LVDS at 200 MSPS. Each mode has its own curve, and the mode is a register choice, not a supply change.

Is 10 bit enough for a digital oscilloscope front end? For a general purpose instrument with a well behaved front end, 9.6 effective bits at 70 MHz leaves the vertical accuracy limited by the amplifier and the reference rather than by the converter.

What has to be checked before using it below 1 GHz with an undersampled input? The clock jitter, the input filter that removes the alias band and the drive network. The 900 MHz bandwidth makes undersampling possible; it does not make the clock requirement disappear.

SUPERB quotes this order code against the exact part number with packing and date codes, and the Component Lead Time Solutions page sets out what to compare when a 10 bit 200 MSPS socket has to be filled from a different source.