ADC10040-Q1
Product Specifications
ADC10040-Q1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADC10040-Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADC10040-Q1: 10 bit 40 MSPS converter run on the automotive grade flow to AEC-Q100 grade 3
ADC10040-Q1 is the automotive release of a low power 10 bit converter, same 3 V single rail and same 55.5 mW, qualified through the automotive flow to grade 3 in a TSSOP body of 28 pins. The ADC10040-Q1 is the automotive version of a 10 bit 40 MSPS converter that runs from a single 3 V rail at 55.5 mW and drops to 13.5 mW in standby. The document covers both the commercial part and the Q version, states that the Q part runs on the automotive grade flow and is qualified to AEC-Q100 grade 3, and gives the same selectable 2.0, 1.5 or 1.0 V peak to peak input range, the same 400 MHz analog bandwidth and the same 28 pin TSSOP body.
Order code and package
| Order code | ADC10040-Q1 |
| Qualification | AEC-Q100 grade 3, automotive grade flow |
| Resolution | 10 bit |
| Conversion rate | 40 MSPS |
| Supply | single 3.0 V rail |
| Full scale | 2.0, 1.5 or 1.0 V peak to peak, selectable |
| Analog bandwidth | 400 MHz at minus 3 dB |
| Power | 55.5 mW at 40 MSPS, 13.5 mW in standby |
| Package | 28 pin TSSOP |
| Temperature | minus 40 to 85 C |
| Base part | the commercial version in the same document |
| Document | SNAS224M, July 2003, revised April 2013 |
Electrical parameters that decide the application
| SNR | 59.6 dB typical at an 11 MHz input |
| DNL | plus or minus 0.3 LSB typical |
| Grade 3 range | minus 40 to 85 C ambient |
| Power per sample | 1.39 nJ at 40 MSPS |
| Standby saving | about 76 percent below the active figure |
| Data rate at 10 bit | 400 Mbps at 40 MSPS |
| Input | differential, on chip sample and hold |
| Architecture | pipeline with digital error correction |
| PPAP support | the automotive flow documentation, requested per programme |
| Supply tolerance | see the recommended operating table for the Q part |
| Package | 28 pin TSSOP, leaded, inspectable |
| Family | shares the document with the commercial order code |
Points to check before this part goes on a BOM
Grade 3 is the point of this order code. AEC-Q100 grade 3 covers an ambient range of minus 40 to 85 C, which is the narrower of the automotive grades, so a programme that needs a hotter part has to look at grade 2 or grade 1 devices rather than assume any Q suffix is enough. The grade belongs in the requirement document before the part number is chosen.
The Q version runs on the automotive grade flow, which is a process and documentation statement rather than a performance one. On the bench the electrical behaviour is the same as the commercial part, so a board can be proven with the commercial order code and then moved to the Q code for production, provided the temperature range of the programme is inside grade 3.
The three selectable full scales matter more in a vehicle than in an instrument, because the sensor interface is often fixed by another supplier. A 1 V sensor output on the 2 V range loses 6 dB of resolution, while the same signal on the 1 V range uses the whole converter, and the selection is a strap rather than a board change.
Standby at 13.5 mW is what makes a duty cycled automotive measurement viable. A sensor that is sampled once a second does not need 55.5 mW continuously, and the wake up time decides whether the saving survives the sampling window. That time is in the electrical table and should be checked against the sampling period rather than assumed.
A 28 pin TSSOP in an automotive assembly is easier to inspect than a QFN, which is a real advantage in a programme with automotive quality gates: the solder joints are visible and the rework process is standard. It also keeps the board cheaper on a low layer count.
At 59.6 dB of typical SNR the practical resolution is about 9.6 effective bits, so a sensor chain planned around 10 bit should expect the last half bit to be lost to converter noise and board noise. Anything that needs 11 or 12 effective bits is on the wrong part and no amount of filtering fixes it.
For procurement the traceability expectations are higher than on a commercial part, and the request for the automotive flow documentation comes with the order rather than after it. A supplier who cannot produce that trail is not offering the same article even when the marking looks right, and this is the field that most often fails an incoming audit.
Grade 3 covers minus 40 to 85 C ambient, and the part is the same converter as the commercial code. That means a board can be proven on the commercial order code and moved to the automotive code for series production, provided the installation point stays inside grade 3 and the process documentation is re-issued for the automotive build.
Where this order code fits
This order code belongs on automotive sensor and actuator boards, in vehicle instrumentation and in under bonnet monitoring where a 10 bit 40 MSPS capture is needed and the build has to be qualified through the automotive flow. It also appears in industrial equipment that is supplied to automotive tier one programmes and therefore has to use parts with an automotive qualification trail. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.
Questions buyers ask
What temperature range does grade 3 cover? Minus 40 to 85 C ambient. A hotter requirement needs grade 2 or grade 1, which is a different part number.
Is the electrical performance different from the commercial part? The document gives the same converter figures. The Q suffix is about the automotive flow and the qualification, not about a different die.
What documentation comes with it? The automotive flow documentation for the programme. It is requested with the order and is part of what makes the part auditable.
SUPERB quotes this order code with date codes and lot traceability on the offer, and the Supplier Quality Audit page lists what an incoming audit should see when an automotive grade part arrives.