LMK03033CISQX/NOPB
Product Specifications
LMK03033CISQX/NOPB
Texas Instruments — Power Management & Signal Chain
Product Overview
The LMK03033CISQX/NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LMK03033CISQX/NOPB: a clock conditioner with the VCO inside
The LMK03033CISQX/NOPB is a precision clock conditioner that integrates an integer N phase locked loop, a voltage controlled oscillator, a partial loop filter and up to eight clock outputs with individual dividers and delay blocks. It takes a clean reference and produces the low jitter clocks that a data converter or a high speed serial link needs, and it does so without an external VCO or a discrete loop filter chain.
The VCO on the 3033 member tunes from 1843 MHz to 2160 MHz, and the divider blocks bring that down to the output frequencies the board needs, with channel dividers from 1 and even values up to 510. The normalized phase noise contribution is minus 224 dBc per hertz, and the family is quoted at 200 fs of RMS clock generator performance from 10 Hz to 20 MHz with a clean input clock, which is the figure that decides whether a converter keeps its effective number of bits at a high input frequency.
Measured at 1843 MHz, the VCO phase noise is minus 86 dBc per hertz at 10 kHz offset, minus 111 at 100 kHz, minus 134 at 1 MHz and minus 152 at 10 MHz. Those numbers are the ones to compare with a converter data sheet, because the close in figure sets the jitter that survives the loop and the far out figure sets the noise that lands in the sampling band.
Key data for the LMK03033CISQX/NOPB
| Function | Integer N PLL, integrated VCO, partial loop filter, up to eight clock outputs with dividers and delay |
| VCO range | 1843 MHz to 2160 MHz on this member, with other members covering 1185 to 1296 MHz and 1470 to 1570 MHz |
| Jitter | 200 fs RMS clock generator performance from 10 Hz to 20 MHz with a clean input, normalized phase noise minus 224 dBc per hertz |
| Phase noise at 1843 MHz | Minus 86 dBc per hertz at 10 kHz, minus 111 at 100 kHz, minus 134 at 1 MHz, minus 152 at 10 MHz |
| Outputs | LVDS and LVPECL buffers, with a divider per output and a programmable delay per output |
| Supply | 3.15 V to 3.45 V single rail |
| Dividers | VCO divider 2 to 8 in all integer values, channel dividers 1 and even values from 2 to 510 |
Body, packing and marking data
| Body | WQFN RHS, 48 pins, 7.0 mm by 7.0 mm by 0.8 mm |
| Packing | 2500 pieces on a large reel |
| Finish | SN plating, moisture level 3 with a 168 hour floor life, 260 C peak |
| Marking | K03033CI printed on the body, which does not name the speed grade |
| Temperature | Minus 40 C to plus 85 C, narrower than a typical industrial isolator |
The temperature range is the first filter
This part stops at 85 C ambient, while most of the other devices on the same card are rated to 125 C. A clock conditioner placed near a power stage will see the high end of its range on a hot day, and a part that is specified to 85 C is the component that decides the cabinet rating. Put it away from the hot side of the board or add a thermal path, and check the junction temperature against the power dissipation rather than the ambient alone.
The loop filter is partially integrated, so the external components that remain set the loop bandwidth and the peaking. A loop that is too wide passes more reference noise and a loop that is too narrow lets the VCO wander. The vendor tooling gives a starting point, and the phase noise plot on the bench is what confirms it.
Where an integrated clock conditioner is used
Data converter clocking, wireless infrastructure, medical imaging and test equipment all use this family. Radar and defence hardware uses the same part where the converter clock has to hold its jitter through a temperature swing, and our defense grade components page covers the traceability those programmes ask for.
On the supply side, the RF component sourcing page is where we list the clock and frequency parts we hold access to, including the older members of this family that are still built into long life equipment.
Questions we get on this code
Buyers ask whether the NOPB suffix is a different part. It is the lead free marking that the vendor prints on the order string, and the row behind it is the same die and the same 2500 piece reel. What it does change is the finish column, which reads SN rather than NIPDAU on this body.
The second question is whether an external VCO would give lower jitter. It can, and it costs board area, a loop filter that has to be tuned by hand and a second supply. For most converter clocks in the 100 MHz to 500 MHz range, the integrated VCO meets the requirement and the integration is what makes the jitter repeatable from unit to unit.