Contact Us

LMK00308SQX/NOPB

Brand: Texas Instruments
Texas Instruments LMK00308SQX/NOPB is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LMK00308SQX/NOPB — Power Management & Signal Chain | Superb Automation

LMK00308SQX/NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The LMK00308SQX/NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LMK00308SQX/NOPB: Eight Differential Outputs From Three Selectable Inputs at 3 GHz

LMK00308SQX/NOPB is a three gigahertz differential clock buffer and level translator in a WQFN (RTA) body of 40 pins. It takes one of two universal inputs or a crystal and fans it out to two banks of four differential outputs plus one LVCMOS output, with each bank set independently to LVPECL, LVDS or HCSL. Additive jitter with a clean source is 20 fs RMS from 10 kHz to 1 MHz at 156.25 MHz, which is why it turns up in front of data converters and line card clocks.

Order code and package

Ordering stringLMK00308SQX/NOPB
FamilyLMK00308 clock buffer, document SNAS576D
PackageWQFN, RTA body, 40 pins, 6.00 mm by 6.00 mm nominal
Reel and packing2500 pieces on a large reel, tin lead finish, no lead in the solder
Moisture levelLevel 3, 260 C peak, 168 hour floor life
Part markingK00308
Smaller reel rowsLMK00308SQ/NOPB at 1000 pieces on a small reel and LMK00308SQE/NOPB at 250
Temperature rangeMinus 40 to plus 85 degrees, industrial grade
Core supply3.3 V plus or minus 5 percent
Output suppliesThree independent VCCO rails at 3.3 V or 2.5 V plus or minus 5 percent

Electrical parameters that decide the application

Input multiplexerThree to one, two universal inputs plus one crystal input
Universal input rangeUp to 3.1 GHz, accepting LVPECL, LVDS, CML, SSTL, HSTL, HCSL or a single ended clock
Crystal input10 to 40 MHz crystal or a single ended clock on the OSCin pin
Output banksTwo banks of four differential outputs, each set to LVPECL, LVDS, HCSL or disabled
Differential output rateUp to 3 GHz
Additive jitter20 fs RMS from 10 kHz to 1 MHz and 51 fs RMS from 12 kHz to 20 MHz with an LMK03806 source at 156.25 MHz
Power supply rejectionMinus 65 dBc on LVPECL and minus 76 dBc on LVDS at 156.25 MHz
LVCMOS outputOne output with a synchronous enable so that it starts and stops without a runt pulse
ConfigurationPin controlled, no serial bus and no register file
Output to output skewSpecified per bank in the switching table, read it before pairing two banks
ThermalThe 6 mm body needs a thermal pad connection on the ground plane to hold the 85 degree limit
Input terminationUniversal inputs accept AC coupling with external bias for CML and LVDS sources

Family variants and how they differ

LMK00308SQ/NOPBThe same die on a 1000 piece small reel, for a pilot build
LMK00308SQE/NOPBA 250 piece small reel row, the practical route for prototypes
LMK00304Four differential outputs from the same three to one multiplexer when eight are too many
LMK00306Six differential outputs, the middle member of the same family
LMK00804BA four output LVCMOS fanout buffer when the load is single ended rather than differential
CDCLVC1310A lower cost fanout buffer for a clock tree that does not need 20 fs additive jitter

Points to check before this part goes on a BOM

The jitter figure belongs to a specific source and a specific offset window. 20 fs RMS is quoted from 10 kHz to 1 MHz with an LMK03806 clock source at 156.25 MHz, and the same part quoted over 12 kHz to 20 MHz reads 51 fs. A specification that copies the first number into an optical or converter budget without the band is comparing two different measurements.

The crystal input stops at 40 MHz. A 100 MHz oscillator cannot be wired to OSCin and must go into one of the two universal inputs, which changes the multiplexer selection and the load on the oscillator. Boards that assume all three inputs are equivalent end up with a clock that never starts.

Three output supplies mean three decoupling networks and three rails to sequence. The part does not enforce an order between VCC and VCCO, but a bank that is enabled while its rail is still rising can put a runt pulse on the clock line, and a converter sampling that line will see it as a valid edge on a short cycle.

There is no serial interface, so every setting is a pin. That is a strength for a line card that must come up without firmware, and a limitation when the same board has to serve two output formats at different times, because changing a bank from LVPECL to LVDS means changing the strapping resistors.

Level translation is real but bounded. A 2.5 V VCCO bank drives a 2.5 V receiver, and a 3.3 V bank drives 3.3 V, but the input side has its own common mode window, and an LVDS source with a 1.2 V common mode has to be AC coupled with a bias network before it reaches the universal input. The document gives the capacitor and resistor arrangement for both the self terminated and the internally terminated receiver cases.

Where the eight outputs go on a converter card

A four converter card with two converters per side needs eight clocks, and the two output banks map onto the two converter groups. Each bank is set to the format the converters expect, LVDS for a low power interface or LVPECL where the receiver wants a wider swing, and the two banks share one input so the converters stay phase aligned.

The LVCMOS output is the spare that keeps the board simple. It carries the same input clock to a field programmable gate array or a microcontroller that does not take a differential clock, and its synchronous enable means it can be stopped during a reconfiguration without producing a narrow pulse that a processor interprets as a valid edge.

What a 20 fs buffer does not fix

An additive jitter figure describes what the buffer adds to a clean input. It says nothing about the jitter that arrives on the input, and nothing about the noise a switching regulator puts on the 3.3 V rail. A board with a 100 fs source and a noisy rail will measure worse than the buffer specification no matter which output format is selected.

Power supply rejection is the number that connects the two, and it is frequency dependent. Minus 65 dBc on the LVPECL outputs at 156.25 MHz is a reasonable rejection, but a 500 kHz switching spur sits in a different part of the curve, and the practical answer is a low noise regulator or an LC filter in front of the core supply rather than a larger capacitor.

Where this order code fits

The part is used where one clean reference has to reach several converters or transceivers in different output formats, and where the clock tree has to come up without firmware. Teams comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does the part need a serial interface to set the output format? No. Every setting is a pin, including the two bits per bank that choose LVPECL, LVDS, HCSL or disable, the input select bits and the enable for the LVCMOS output. That keeps the bring up deterministic but means a format change needs a board change.

Can one bank run at 2.5 V while the other runs at 3.3 V? Yes. There are three independent VCCO rails, two for the differential banks and one for the LVCMOS output, and each is specified at 3.3 V or 2.5 V plus or minus 5 percent. The core supply stays at 3.3 V regardless.

What is the smallest reel available? The 250 piece small reel row, LMK00308SQE/NOPB. The plain SQ string ships 1000 pieces and the SQX string 2500, so a pilot build of fifty boards should be ordered against the E row rather than opened from a production reel.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.