Contact Us

INA2132UA/2K5

Brand: Texas Instruments
Texas Instruments INA2132UA/2K5 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2132UA/2K5 — Power Management & Signal Chain | Superb Automation

INA2132UA/2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2132UA/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2132UA/2K5: Dual low-power difference amplifier in SO-14

INA2132UA/2K5 is a dual unity-gain difference amplifier with a trimmed resistor network on each channel in a SO body of 14 pins. Each channel is a precision amplifier with a 40 kilohm input network, a gain of one, 90 dB of common-mode rejection, plus or minus 0.05 percent maximum gain error, 160 microamp of supply current per amplifier, and a supply window from 2.7 V to 36 V single ended.

Order code and package

Ordering stringINA2132UA/2K5, U package grade, tape and reel of 2500
Package14-pin SO surface mount
GradeThe A grade is the tighter offset grade, plus or minus 500 microvolt maximum
Ambient range-40 C to 85 C, with operation specified to 125 C
ChannelsTwo independent difference amplifiers in one body

Electrical parameters that decide the application

GainUnity, set by the internal 40 kilohm network
Common-mode rejection90 dB typical
Gain errorPlus or minus 0.05 percent maximum, 0.001 percent nonlinearity
Supply range2.7 V to 36 V single supply, or plus and minus 1.35 V to plus and minus 18 V
Quiescent current160 microamp per amplifier
Bandwidth300 kHz small signal, 0.1 V per microsecond slew rate
Thermal resistance100 C/W junction to ambient

Points to check before this part goes on a BOM

The input resistors are ratio matched to 0.01 percent but their absolute value is only within 20 percent, which is the detail that decides what this part can and cannot do. Ratio matching gives the 90 dB of common-mode rejection and the 0.05 percent gain error; the loose absolute value means the input impedance is 40 kilohm give or take a fifth, so a source with a significant output impedance sees a gain that depends on the part. For a bridge or a shunt with a low impedance, that is irrelevant; for a high-impedance sensor it is the dominant error.

The common-mode range extends to the negative supply and stops 1 V below the positive one. On a single 5 V supply that means the input can sit at ground, which is what a ground-referenced shunt needs, but it cannot sit at 5 V. A high-side sense resistor in a 5 V system is exactly the case this part does not cover, and the family member with a wider common-mode range is the part for that job.

At 100 C/W in a 14-pin SO, the package is the thermal limit long before the 160 microamp per channel becomes one. The part is a signal chain device and dissipates milliwatts, so the number matters only when it is asked to drive a heavy load; the output current limit of about 12 mA into a short is where the package starts to warm.

Offset of plus or minus 500 microvolt maximum on the A grade is the DC accuracy floor. On a 50 mV full-scale shunt that is 1 percent, which is the same order as a 1 percent sense resistor, so the offset and the resistor together set the accuracy of the measurement and neither can be ignored. Offset drift of about 10 microvolt per degree C over the industrial band adds a second term that is not in the room-temperature number.

300 kHz of bandwidth with a 0.1 V per microsecond slew rate is a slow part by modern standards and a deliberate one: it filters switching noise from the measurement instead of adding a filter that would introduce its own phase shift. A current loop that samples at a few kilohertz is well served; a control loop that needs to see a transient inside 10 microseconds is not.

Two channels in one package share a supply and a thermal pad but not a reference, so each channel can be referenced independently. Channel separation is specified at 0.04 microvolt per volt, which means a full-scale swing on one channel moves the other by about 1 microvolt at a 25 V output, small enough that two measurements in one package behave like two separate parts.

Ten nanofarads of capacitive load is the stability limit, and it is low because the part drives through the same 40 kilohm network that sets its gain. A cable or a long trace to a measurement point adds capacitance and can push the output into a slow ring that looks like noise on the reading. A series resistor at the output is the usual fix, and it trades bandwidth for stability in a part that has bandwidth to spare at 300 kHz.

Where this order code fits

It fits a differential current sense across a ground-referenced shunt, a ground-loop breaking stage in an instrumentation chain, or a summing and inverting stage, where the accuracy demand is a fraction of a percent and the bandwidth demand is modest. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the ADC DAC Cross Reference page.

Questions buyers ask

Can the two channels be used as a single instrumentation amplifier? Yes, with an external gain stage, which is one of the documented configurations. The internal network sets unity gain per channel, so any gain above one comes from components outside the part and their tolerance adds to the 0.05 percent.

Is the offset grade the only difference between U and UA? No. The A grade has the tighter offset limit, and the ordering string has to state the grade. A substitution between grades changes the DC accuracy of the measurement even though the pinout and the function are identical.

Why is the input impedance only specified loosely? Because the resistors are ratio matched rather than absolutely trimmed. The part is intended for low-impedance sources, where the absolute value does not set the gain, and the 20 percent figure is the honest description of that resistor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.