Contact Us

INA163UA/2K5

Brand: Texas Instruments
Texas Instruments INA163UA/2K5 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA163UA/2K5 — Power Management & Signal Chain | Superb Automation

INA163UA/2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA163UA/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA163UA/2K5: one nanovolt per root hertz for a microphone preamp

The INA163 is an instrumentation amplifier built for low level audio, with a voltage noise density of 1 nV per root hertz at 1 kHz and a total harmonic distortion plus noise of 0.002 per cent at 1 kHz into a gain of 100. Those two numbers are what a moving coil cartridge, a dynamic microphone or a low output ribbon needs, because the amplifier's own noise sets the floor of the recording and the distortion sets the character of the sound. The current feedback topology keeps 800 kHz of bandwidth at a gain of 100, so the loop has enough speed to stay linear through a transient instead of rounding it.

Gain is set with one external resistor and the equation is the standard instrumentation form, so a console can offer a switched gain range from a single component change per step. Common mode rejection is above 100 dB, which is what allows a balanced microphone line to arrive on a stage full of lighting dimmers without the hum becoming part of the recording. The part runs on split rails from plus or minus 4.5 V to plus or minus 18 V, so it fits both a battery powered field recorder and a mains powered console channel strip, and the output drives a 600 ohm load at console level.

Key data for the INA163UA/2K5

Noise1 nV per root hertz at 1 kHz, which is the number that decides the recording floor at low gain
Distortion0.002 per cent total harmonic distortion plus noise at 1 kHz into a gain of 100
Bandwidth800 kHz at a gain of 100, held by the current feedback topology rather than a fixed product
RejectionCommon mode rejection above 100 dB, enough for a microphone line in a stage lighting environment
GainSet with one external resistor using the standard instrumentation equation, no internal gain steps
SupplySplit rails from plus or minus 4.5 V to plus or minus 18 V, output drives a 600 ohm console load

Body, marking and reel data

BodyD, SOIC 14 pin, INA163UA/2K5 at 2500 pieces on a large reel, 330 mm carrier
TubeINA163UA in a tube of 50 pieces for bench work and repair
FinishNIPDAU, moisture level 3 with a 168 hour floor life at 260 C
GradeAmbient minus 40 C to 85 C on both packings, no automotive grade in this family

Where the noise figure is the whole specification

In a microphone preamp the first amplifier sets the noise floor for everything behind it, and a 4 nV part in a gain of 100 stage adds about 12 dB more noise than a 1 nV part does. That difference is audible on a quiet recording and it cannot be recovered later, which is why this part survives in consoles that were built decades ago. The distortion cancellation circuit inside the device is the second reason: at high gain the input pair runs with a small differential voltage, and the correction keeps the third harmonic down where a simple long tailed pair would push it up.

The same qualities serve industrial and medical instruments that measure a low level transducer, such as a moving coil, a strain gauge bridge or a geophone. Where a customer is replacing a discontinued preamp and needs the same noise figure, our amplifier cross reference lists the low noise instrumentation families by noise density and supply, and the obsolete part cross reference hub sets out what a documented substitute has to prove before it is accepted in an audio signal path.

Buyer questions on the INA163UA/2K5

What gain resistor gives 100 V/V? The data sheet equation takes one resistor between the gain pins, and the table gives the value for each standard gain. The 0.002 per cent distortion figure is quoted at a gain of 100, so that setting is the one the vendor characterised most thoroughly.

Does the part need a heat sink at plus or minus 18 V? The SOIC 14 body dissipates more at high supply and low load, so the junction temperature is checked against the ambient in the enclosure. At console levels the load current is small and the rise is modest.

Is the input protected against phantom power? Not internally. A console applies 48 V phantom power through 6.8 kilohm resistors, and the coupling capacitors at the input block it. The amplifier's input stage must never see that voltage directly.

Availability and ordering notes

This is a long lived audio part with an active reel and tube row, and the reel is the packing production buys. Because the part sits at the front of a signal chain, a substitute has to be checked for noise density, distortion at the working gain and common mode range rather than for pin compatibility alone. We hold the reel, confirm the date code against the customer's build date, and quote the date code management record with the shipment.