INA141U/2K5
Product Specifications
INA141U/2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA141U/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA141U/2K5: a precision instrumentation amplifier with a two position gain switch
The INA141 is a three operational amplifier instrumentation amplifier whose gain is set by a jumper rather than by a resistor. With the gain pins left open the gain is 10 V/V, with them shorted it is 100 V/V, and a resistor between the pins sets anything in between, so a board can offer two calibrated ranges with a switch and no trimming in the field. The current feedback topology keeps the bandwidth wide at high gain, 200 kHz at a gain of 100, which is unusual for a part that draws so little supply current. Common mode rejection is 117 dB at a gain of 100, so a thermocouple or a bridge sitting on top of a large offset still reads as a small signal.
The input stage is laser trimmed for offset and offset drift, which is what allows the part to be used without a trim pot in a production instrument. Slew rate is 4 volts per microsecond with a 50 per cent input overload, so a step at the input settles without the long tail that a low power amplifier usually shows. The reference pin allows the output to be shifted for single supply operation, and the same pin is where an offset calibration voltage is injected when a channel needs to be nulled at test.
Key data for the INA141U/2K5
| Gain | 10 V/V with the gain pins open, 100 V/V with them shorted, any value between with one resistor |
| Rejection | Common mode rejection 117 dB at a gain of 100, which is the figure that matters on a bridge input |
| Bandwidth | 200 kHz at a gain of 100, held by the current feedback topology rather than by a fixed gain bandwidth product |
| Slew | 4 volts per microsecond with a 50 per cent input overload, so a step settles without a long tail |
| Supply | Split rails from plus or minus 2.25 V to plus or minus 18 V, low quiescent current for a battery instrument |
| Trim | Laser trimmed offset and drift, reference pin for level shifting and for calibration injection |
Body, marking and reel data
| Body | D, SOIC 8 pin, INA141U/2K5 at 2500 pieces on a large reel, 330 mm carrier |
| Tube | INA141U in a tube of 75 pieces for bench and repair work |
| Finish | NIPDAU, moisture level 3 with a 168 hour floor life on the reel row |
| Grade | Ambient minus 40 C to 85 C, the standard industrial range for this family |
Where the jumper gain matters
Most instrumentation amplifiers need a resistor whose value sets the gain, and that resistor becomes the accuracy limit at high gain because a 1 per cent resistor gives a 1 per cent gain error before the amplifier is even considered. The INA141 removes that for the two gain settings it offers, because the ratio is trimmed inside the package. A weigh scale front end can therefore offer a 10 V/V range for a full load and a 100 V/V range for a small load without a second calibration, which is the difference between one test station and two.
The part suits bridge transducers, strain gauges, thermocouples and low level current shunts, and it is often the amplifier behind a 16 bit converter in an industrial transmitter. Where a customer needs a pin compatible alternative after a supply problem, our amplifier cross reference lists the instrumentation families by gain method and common mode range, and the BOM shortage recovery page sets out how a missing amplifier is covered without changing the board.
Buyer questions on the INA141U/2K5
Can the gain be set to 50? Yes. A resistor between the two gain pins sets any value between 10 and 100, and the data sheet gives the equation and the resistor table. The trimmed 10 and 100 settings are still the two with the tightest gain error.
Does the reference pin affect the common mode range? It shifts the output, not the input window. The inputs still have to stay inside the amplifier's common mode range, which is why a single supply bridge is biased to the middle of the rail rather than to ground.
Is the part stable with a capacitive load? It drives a cable or a converter input directly up to the load the data sheet specifies. Above that, a series resistor at the output is the usual fix, and the value is chosen against the settling requirement.
Availability and ordering notes
The reel of 2500 covers a production run and the tube of 75 covers bench work, and both are active in the current addendum. Where a customer's instrument has been in the field for years, the amplifier is usually the part that fails last, so the supply risk is low and the substitution risk is high. We check the gain method, the common mode range and the reference topology before offering an alternative, and the comparison is recorded in the drop in verification note that ships with the quote.