INA137UA/2K5
Product Specifications
INA137UA/2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA137UA/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA137UA/2K5: a differential line receiver for balanced audio that rejects ground noise
The INA137 is a differential line receiver built from an operational amplifier and a laser trimmed resistor network, with a fixed gain of plus or minus 6 dB, which is a gain of 2 or a gain of one half depending on which way the input pair is wired. Its job is to take a balanced audio pair that has travelled down a cable and turn it into a single ended signal while rejecting whatever noise the two conductors picked up in common. Common mode rejection is 90 dB typical, distortion is 0.0005 per cent at 1 kHz, and the slew rate is 14 volts per microsecond, so a professional audio chain keeps its headroom and its transient edges.
The supply range is plus or minus 4 V to plus or minus 18 V, which covers both a 9 V battery instrument and a rack unit running on regulated 15 V rails, and quiescent current is 2.9 mA maximum. Settling to 0.01 per cent takes 3 microseconds, which matters when the receiver feeds a multiplexer that switches between sources. The reference pin allows the output to be offset for a single supply stage, and the same resistor network that sets the gain also sets the input impedance, so the loading on the cable is defined rather than dependent on the source.
Key data for the INA137UA/2K5
| Gain | Fixed plus or minus 6 dB, a gain of 2 or one half by reversing the input pair, no external resistors |
| Rejection | Common mode rejection 90 dB typical, which is the figure that sets how much hum reaches the output |
| Distortion | 0.0005 per cent at 1 kHz, measured with the vendor's audio test circuit |
| Speed | Slew rate 14 volts per microsecond, settling to 0.01 per cent in 3 microseconds |
| Supply | Plus or minus 4 V to plus or minus 18 V, quiescent current 2.9 mA maximum |
| Noise | Output noise floor quoted in the audio table, low enough for a microphone preamp stage |
Body, marking and reel data
| Body | D, SOIC 8 pin, INA137UA/2K5 at 2500 pieces on a large reel, 330 mm carrier |
| Dual | INA2137 in PDIP 14 and SOIC 14, two independent receivers on one die, 25 pieces per tube in PDIP |
| Grade | Ambient minus 40 C to 85 C, which covers rack equipment and portable recorders |
| Finish | NIPDAU on the active rows, moisture level 2 with a one year floor life where the row prints it |
Where a differential receiver saves a product
A balanced line exists because a cable in a rack picks up interference from mains wiring, switching supplies and radio equipment. The interference arrives on both conductors almost equally, so a receiver that subtracts the two cancels it while keeping the wanted difference. A receiver built from a general purpose operational amplifier and four 1 per cent resistors gives about 40 dB of rejection, which is not enough to keep a 60 Hz hum below the noise floor of a 24 bit converter. The trimmed network in this part takes that to 90 dB typical, and it does so with one component and no adjustment.
The audio chain is also where a part change is heard rather than measured, so a substitute is only accepted after a distortion and crosstalk check at the working level. Where a board has to move to a dual receiver, the INA2137 pairs share the same silicon and the same pin function, so two channels fit one package. Our amplifier cross reference lists the members of this family by channel count and package, and the pin to pin cross reference page covers the bodies that share this pinout.
Buyer questions on the INA137UA/2K5
Does the part need a split supply? It is specified on split supplies from plus or minus 4 V to plus or minus 18 V. A single supply works if the reference pin is biased to half the rail and the input signals stay inside the common mode window.
How is the gain changed to 2? The input pair is reversed, which flips the sign of the transfer and gives a gain of 2 in the same package. No resistor is added, so the rejection and the distortion figures hold.
Is this the same silicon as the INA2137? Yes. The INA2137 is the dual version with two independent receivers on one die, and the two channels are kept separate enough that an overload on one does not disturb the other.
Availability and ordering notes
This is a mature part that has been in audio equipment for decades, so the risk is availability rather than performance. The 2500 piece reel covers a production run and the PDIP dual body covers bench work. Where a customer's board was written around a part that has since gone quiet, our obsolete part replacement route starts from the pin function and the network rather than from the part number, because an audio receiver is defined by its resistor ratio and its supply range.