INA129U/2K5
Product Specifications
INA129U/2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA129U/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA129U/2K5: precision low power instrumentation amplifier with a 49.4 kOhm gain term in the eight pin SOIC
INA129U/2K5 is a three op amp instrumentation amplifier from the INA12x family, the member whose gain equation uses 49.4 kOhm so it lands in sockets that expect that resistor value in a SOIC body of 8 pins. It takes a single external resistor for any gain from 1 to 10000, runs from plus or minus 2.25 V to plus or minus 18 V, draws 700 uA typical and 750 uA maximum, and holds a 50 uV offset limit with 0.5 uV per degree of drift. Inputs survive plus or minus 40 V, and the part is specified from minus 40 to plus 85 degrees rather than the 125 degrees of the newer precision parts.
Order code and package
| INA129U/2K5 | SOIC D body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 15 October 2026, moisture level 3 with a 168 hour floor life, and the finish and RoHS columns print Call TI on this row rather than a material name |
| INA129U/2K5G4 | the same SOIC body and the same 2500 piece reel with a NIPDAU finish, RoHS Yes and moisture level 2 with a one year floor life, marking 129U, which is the row to order when a material declaration is required |
| INA129U | SOIC D body in a 75 piece tube, moisture level 3, which is the repair quantity |
| INA129UA | the A grade in the same SOIC body, a separate row in the addendum, with its own 75 piece tube and 2500 piece reel entries |
| INA129P | PDIP P body, 8 pins, 50 pieces in a tube, the through hole option for an existing board |
Electrical parameters that decide the application
| Offset voltage | 50 uV maximum referred to the input, with the gain term dividing the output stage contribution the same way the INA821 does |
| Offset drift | 0.5 uV per degree maximum over minus 40 to plus 85 degrees |
| Gain equation | 1 plus 49.4 kOhm divided by RG, gain range 1 to 10000, against 50 kOhm for the INA128 in the same family |
| Gain error | 0.01 per cent typical and 0.024 per cent maximum at unity gain, widening at higher gain and differing between the two chip site origins |
| Common mode rejection | 120 dB minimum, quoted with a 1 kOhm source imbalance across the input range |
| Input bias current | 5 nA maximum from the SHE chip site origin, 0.7 nA maximum from the FRE origin, a seven fold difference on the same order code family |
| Voltage noise | 8 nV per root hertz and 0.2 uV peak to peak from 0.1 Hz to 10 Hz on the SHE origin, 6.9 nV per root hertz on the FRE origin |
| Bandwidth | 1.3 MHz at G equal to 1, 640 kHz at G equal to 10, 200 kHz at G equal to 100 and 20 kHz at G equal to 1000 |
| Slew rate | 4 V per microsecond, with 12 us settling to 0.01 per cent at low gain and 80 us at G equal to 1000 |
| Input range | 2 V inside each rail, so a plus or minus 15 V supply gives plus or minus 13 V of common mode and the safe input voltage is plus or minus 40 V |
| Supply and current | plus or minus 2.25 V to plus or minus 18 V, 700 uA typical and 750 uA maximum, with the current quoted as a plus or minus figure in the electrical table |
| Temperature range | minus 40 to plus 85 degrees, which is narrower than the 125 degrees of the INA821 and is the reason the two are not interchangeable on a hot board |
Family variants and how they differ
| INA129 against INA128 | the two differ only in the gain resistor, 49.4 kOhm against 50 kOhm, which is a 1.2 per cent difference in the gain term and the reason the INA129 exists as a drop in for sockets built around the 49.4 kOhm value |
| SHE against FRE chip site origin | bias current 5 nA against 0.7 nA, noise 8 nV against 6.9 nV per root hertz, and separate gain error windows, all printed as two columns in the same electrical table under one order code family |
| INA828 as the newer alternative | 0.6 nA maximum bias current and 7 nV per root hertz of noise at the same supply current, which is the part to compare when the bias current of the SHE origin is the limiting error |
| INA2128 | the dual version of the INA128, so a two channel board built around the 50 kOhm term has a dual option while the 49.4 kOhm term does not |
| Tube against reel | the 75 piece tube and the 2500 piece reel are the same silicon, but the tube row and the reel row are separate lines in the addendum with their own moisture level entries |
Points to check before this part goes on a BOM
The revision history in this document explains a lot about the electrical table. Revision G added separate fabrication process specifications for bias current, noise, bandwidth, slew rate, settling time and short circuit current, so the same catalogue string can now be a 5 nA part or a 0.7 nA part depending on which wafer it came from. A board whose error budget assumed 5 nA is safe, and a board that needs 0.7 nA has to be checked against the origin on the reel label rather than against the part number.
Gain error is quoted per gain and per origin, and the unity gain row is the tightest at 0.01 per cent typical. The gain of 1000 row widens to a limit that is several times larger, which is the resistor term rather than the amplifier: at high gain the 49.4 kOhm term inside the device is in series with a 49 Ohm external resistor and any error in either one lands directly on the gain.
The 1.3 MHz at unity gain falls to 200 kHz at a gain of 100 and 20 kHz at a gain of 1000. That is a constant gain bandwidth product of about 20 to 26 MHz, unlike the current feedback stage in the INA821 which holds bandwidth better at high gain, so a stage that needs speed at high gain should not be built on this part simply because the offset is adequate.
The 85 degree temperature ceiling is the practical difference from the newer precision parts. A transmitter that runs its electronics at 90 degrees ambient needs a different device even though the offset and the gain term would otherwise suit, and the ceiling applies to the A grade as well.
The input window of 2 V inside each rail means a plus or minus 15 V supply gives about plus or minus 13 V of common mode, which is why this part appears in industrial transmitters that already carry a plus or minus 15 V rail. On a single 5 V rail the window is between 2 V and 3 V and a ground referenced bridge does not fit, the same constraint the INA821 carries.
The moisture level difference between the plain row and the G4 row is worth reading before a reflow profile is signed off. The plain reel is level 3 with a 168 hour floor life, the G4 reel is level 2 with a year, and the parts are electrically identical, so the suffix that gets ordered decides whether the line needs a dry pack schedule at all.
What the 49.4 kOhm term changes in practice
Gain is 1 plus 49.4 kOhm divided by RG, so a gain of 100 needs 499 Ohm and a gain of 1000 needs 49.45 Ohm, while the INA128 with its 50 kOhm term needs 505 Ohm and 50.05 Ohm for the same two gains. The difference is 1.2 per cent on the gain, which matters when a socket was built around a resistor value that a predecessor part expected and the board is not being reworked.
Reading the two origin columns
The electrical table prints the input bias current as two rows under one order code: 5 nA maximum for the SHE origin and 0.7 nA maximum for the FRE origin, with the noise figures separated the same way. A purchase specification that names only the part number does not pin either, so an incoming inspection of a high impedance board should measure bias current on a sample rather than assume the tighter column.
The short circuit current and the bandwidth are also split by origin in this revision, which is unusual enough that the note in the revision history was added deliberately. The safe reading is that every row with a CSO label is a limit for one wafer source, and the reel label is the only place the source is visible.
Where this order code fits
Pressure transmitters, temperature transmitters, weigh scales, ECG front ends, analogue input modules and data acquisition are the applications the vendor names, and the common thread is a bridge or a thermocouple on a long cable where a few nanoamps of bias current turns into a millivolt of error. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is the INA129U/2K5 the same silicon as the INA128U/2K5? No. The gain term differs, 49.4 kOhm against 50 kOhm, so a resistor chosen for one gives about 1.2 per cent gain error on the other.
What moisture level does the plain reel carry? Level 3 with a 168 hour floor life. The G4 row of the same body is level 2 with a one year floor life.
Does the part work at 105 degrees? No. The specified range stops at 85 degrees for both grades.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.