Contact Us

VBQG5222

Brand: VBsemi
VBsemi VBQG5222 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG5222 — Discrete & Power Semiconductors | Superb Automation

VBQG5222

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG5222 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG5222: an N and a P channel side by side in 2 by 2 mm

The VBQG5222 is a dual MOSFET with one N channel and one P channel in a DFN body of 2 by 2 mm. Both are rated at plus or minus 20 V drain to source, the gate window is plus or minus 12 V, the thresholds are 0.8 V for the N channel and minus 0.8 V for the P channel, the current is plus or minus 5 A, and the on resistance is 24 milliohm for the N channel and 40 milliohm for the P channel at both 2.5 V and 4.5 V gates, falling to 20 and 32 milliohm at 10 V.

A complementary pair in one package is a deliberate product. It exists so that a half bridge or a push pull stage can be built without a bootstrap supply, because the P channel high side turns on when its gate is pulled below the source. That removes a capacitor, a diode and a driver channel, at the cost of a P channel that is larger and slower than the N channel beside it.

The 12 V gate window is the first thing to notice. It is the narrowest in this catalogue band, and it decides the drive arrangement before anything else does.

Key data for the VBQG5222

ConfigurationDual, one N channel and one P channel
PackageDFN 2 by 2 mm, exposed pad, surface mount
VDSPlus or minus 20 V
VGSPlus or minus 12 V
Vth, N channel0.8 V
Vth, P channelMinus 0.8 V
IDPlus or minus 5 A
RDS(on), N channel24 milliohm at 2.5 V and 4.5 V, 20 milliohm at 10 V
RDS(on), P channel40 milliohm at 2.5 V and 4.5 V, 32 milliohm at 10 V
TechnologyTrench
MatchingThe two channels are not resistance matched, the P channel is about two thirds of the N channel
Thermal pathExposed pad shared by both dies

The 2.5 V column that does not move

Both channels publish the same resistance at 2.5 V and at 4.5 V. That is unusual, and there are two readings. The optimistic one is that the die is so steep that the channel is fully formed by 2.5 V, which for an 0.8 V threshold is plausible. The cautious reading is that the 2.5 V column was measured at a low current and the number is a floor rather than an operating point.

For a battery powered product the difference matters. A single cell lithium pack runs from 4.2 V down to 3.0 V, and a 2.5 V drive column that holds 24 milliohm is a promise that the part works to the end of the discharge curve. If the column is a floor, the resistance at 3 V might be a third higher and the efficiency at the bottom of the curve is worse than the table suggests.

The safe method is the same one that applies to every catalogue table: find the gate voltage the circuit applies at the worst operating corner, and look at the output characteristic at that voltage. For a part with an 0.8 V threshold and a 12 V gate window, a 3.3 V gate drive is inside the window and gives a real overdrive of 2.5 V, which is normally enough for a logic level die.

Using a P channel high side without a bootstrap

A complementary pair saves the bootstrap, and it saves it in a way that is easy to see in the circuit. The P channel source ties to the positive rail, its gate goes to the midpoint through a resistor and a small N channel to ground, and it turns on when the midpoint is pulled low. No floating supply, no capacitor to charge, no refresh interval at 100 per cent duty.

Two things follow. The P channel is on whenever its gate is low, so a fault that holds the gate low keeps the high side on, which is the opposite of the fail safe behaviour of a bootstrapped N channel. And the turn off is through a resistor to the rail, so the speed is set by the resistor and the gate capacitance, which is slower than an active pull up.

The resistance asymmetry, 24 against 40 milliohm, means the high side and low side of a bridge built from this part do not share loss equally. In a 5 V to 3.3 V converter with a 50 per cent duty, the P channel conducts half the time at 40 milliohm and the N channel the other half at 24, so the P channel dissipates two thirds of the conduction loss. That is the price of the simpler drive.

Where this pair belongs

Use it in a 12 V or lower rail, in a bridge or push pull stage under about 2 A, in a signal level bidirectional switch, or as a complementary output stage. Do not use it as a main power stage above 3 A, and do not use it where the 12 V gate window would be exceeded by a supply transient, because the window is the tightest parameter on the page.

Our guide to verifying a drop in replacement covers the check sequence for a complementary pair, where the pin map, the threshold pair and the gate window all have to match before the resistance comparison means anything.

The sourcing side of this part is covered on the component shortage forecast. For a complementary pair that sits on a control rail, that page covers how a shortage is seen before it stops a line.

Questions we get on this code

Can the P channel be used alone as a load switch? Yes, and it is a good use of the part, because 40 milliohm at 5 A is 1 W which is at the edge of the body but workable at 3 A. Keep the gate below the source and clamp the gate to source at 12 V.

Why is the P channel resistance higher? P channel silicon has lower carrier mobility, so the same die area gives a higher resistance. It is a property of the material, not a defect.

Will it work at 3.3 V gate drive? The thresholds say yes, with 2.5 V of overdrive. Ask for the output characteristic at 3.3 V before relying on the 24 milliohm figure at that voltage.

What is the reel size and the date code policy? Reel size is confirmed on the quotation. For a 20 V complementary pair we normally quote current production with a date code inside twelve months unless the customer asks for a specific window.