VBQF3310G
Product Specifications
VBQF3310G
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF3310G from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF3310G: a half bridge in one 3 by 3 mm package
The VBQF3310G puts two N channel dies into a single DFN body of 3 by 3 mm, wired as a half bridge. The catalogue lists a 30 V drain to source rating for both devices, a plus or minus 20 V gate window, thresholds of 1.7 V, a 35 A current figure, 16 milliohm at a 4.5 V gate and 9 milliohm at 10 V, on trench silicon.
Two dies in one package is a different product from two discrete parts, and the difference is not only board area. The loop between the high side source and the low side drain is inside the package, which removes the source inductance of the high side device from the switching loop and takes a large part of the switch node ringing with it. That is the reason a half bridge package exists at all.
The cost is thermal. One body has to pass the loss of both devices, and in a synchronous buck the low side carries the larger share at high duty while the high side carries the switching loss. A 3 by 3 mm pad has to be treated as a single thermal node, not as two.
Key data for the VBQF3310G
| Configuration | Half bridge, two N channel dies, high side and low side in series |
| Package | DFN 3 by 3 mm, exposed pad, surface mount |
| VDS | 30 V per device |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V typical |
| ID | 35 A |
| RDS(on) at 4.5 V | 16 milliohm |
| RDS(on) at 10 V | 9 milliohm |
| Technology | Trench |
| Gate drive | High side needs a floating supply, the catalogue page does not publish a bootstrap diode |
| Pin map | Not published on the catalogue page, request the data sheet before committing a footprint |
| Thermal path | One exposed pad carries both dies |
The high side gate needs a supply that the part does not provide
A half bridge in a package is still a half bridge. The high side source sits on the switch node, so its gate has to be driven from a supply that rides on that node, which means a bootstrap capacitor and a diode to the low side rail, or an isolated driver. Nothing in the package supplies that, and the catalogue page does not list a bootstrap diode inside.
That is not a defect, it is the normal arrangement, but it decides the driver choice before the part is chosen. A single channel high and low side driver with a bootstrap pin is the usual partner. The bootstrap capacitor has to be sized for the gate charge of the high side die, and gate charge is one of the parameters this catalogue page does not publish, so the figure has to come from the data sheet before the capacitor is fixed.
The other consideration is dead time. Both dies are on one die paddle and both gates come out to separate pins, so shoot through is entirely a driver timing question. A driver with programmable dead time in the 20 to 100 nanosecond range is what this class of part expects, and a fixed 200 nanosecond dead time costs efficiency at high switching frequency or risks a body diode conduction interval at low frequency.
Matching the two dies to a duty cycle
The catalogue quotes one resistance pair for the package, 16 milliohm at 4.5 V and 9 milliohm at 10 V, without separating the high side from the low side. In most commercial half bridge packages the two dies are the same size, which is a compromise: the high side wants low gate charge and the low side wants low resistance.
For a 12 V to 1.2 V converter running at 10 per cent duty, the low side conducts for 90 per cent of the period and its conduction loss dominates. At 20 A and 9 milliohm that is 3.24 W in the low side, which is more than a 3 by 3 mm pad wants to pass on its own, so either the current comes down or the package grows. For a 12 V to 5 V converter at 40 per cent duty, the split is closer to even and the same part runs far cooler.
Switching loss is the other half. At 500 kHz with a 12 V input and 10 nC of gate charge, the driver loss alone is measurable, and the crossover loss depends on the gate resistor and the driver current rather than on the die. Two 30 V dies in one body with a 1.7 V threshold are a good match to a 5 V gate drive, which is what most integrated drivers deliver.
Where the package earns its place, and where it does not
Use the part where the board space is tight, where the switch node loop has to be short, and where the current is under about 15 A. Do not use it where the two devices need different die sizes, where the loss is dominated by a long low side conduction interval at high current, or where a fault on one device has to be isolated from the other.
Our BOM scrubbing page covers how a bill of material is checked before release, and a two die package is exactly the kind of line where a package change looks harmless on the bill and changes the footprint, the pad, the driver and the thermal model at once.
The sourcing side of this part is covered on the supplier scorecard. For a two die package that only a few sources build, that page covers how a source is scored across a programme.
Questions we get on this code
Can the two dies be used as two independent switches? Only if the pin map exposes the junction between them and both sources separately. That is a data sheet question, and the catalogue page does not answer it. Do not assume independence from the phrase half bridge.
Is 30 V enough for a 24 V input? No. A 24 V rail with ringing reaches 30 V and the switch node overshoot adds to it. Use a 40 V or 60 V class part for a 24 V input, and keep the 30 V class for 12 V and below.
What gate drive voltage should the board supply? 10 V gives the 9 milliohm column and is the efficient choice. 4.5 V gives 16 milliohm, which is fine for a 10 A load and lets a 5 V logic driver be used directly.
Do you quote this part from stock or from allocation? We quote what is confirmed at the time of the request. A half bridge package in a 3 by 3 body is a single source item for most boards, so the date is confirmed before it is promised.