VBQF2305
Product Specifications
VBQF2305
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF2305 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF2305: a 30 V P channel that carries 52 A in a 3 by 3 mm body
The VBQF2305 is a single P channel MOSFET with a minus 30 V drain to source rating, a plus or minus 20 V gate window and a threshold of minus 3 V. The catalogue quotes a drain current of 52 A, an on resistance of 5 milliohm at a 4.5 V gate and 4 milliohm at 10 V, trench silicon and a DFN body of 3 by 3 mm.
A P channel at that current and that resistance is not a commodity small signal part. P channel silicon carries roughly two to three times the specific resistance of N channel silicon at the same voltage class, so a die that reaches 4 milliohm at 30 V is a large die in a small package, and the whole of its thermal budget leaves through the exposed pad on the underside.
That combination is exactly what a high side switch wants when a charge pump is not available or not wanted. Reverse polarity protection on an input connector, a battery disconnect that sits in the positive lead, a load switch on a 24 V rail, a bridge that is driven from a single ended gate signal: all of those are places where a P channel removes the bootstrap supply and the level shifting that an N channel would need.
Key data for the VBQF2305
| Configuration | Single P channel |
| Package | DFN 3 by 3 mm, exposed pad, surface mount |
| VDS | Minus 30 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 3 V typical |
| ID | Minus 52 A |
| RDS(on) at 4.5 V | 5 milliohm |
| RDS(on) at 10 V | 4 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, ask for the curve before sizing a driver |
| Body diode | Intrinsic, anode at drain in the P channel sense, so it conducts when the drain is above the source |
| Thermal path | Exposed pad to board copper, the lead frame is not the path |
A minus 3 V threshold and a 4.5 V gate column need reading together
Take the two published numbers at face value and there is a tension. A threshold of minus 3 V means the channel is only beginning to form when the gate sits 3 V below the source. At a 4.5 V gate the overdrive is 1.5 V, and a die that delivers 5 milliohm at 1.5 V of overdrive would be an unusually steep device for a 30 V P channel.
There are two possible explanations and they lead to different decisions. Either the 4.5 V column was measured on a typical die at 25 C with the gate held well below the threshold in the sense of a full rail drive, which is the normal way catalogue tables are built, or the threshold is quoted for a low current point that sits far down the transfer curve. In both cases the number that decides a real board is the resistance at the gate voltage the circuit actually applies, and that only comes from the output characteristic in the data sheet.
For a 12 V rail switched by a P channel, the gate is normally pulled to ground through a resistor or a small N channel, so the gate sees the full 12 V and the 10 V column applies. For a 5 V rail the gate sees 5 V and the 4.5 V column is the right one. For a 3.3 V rail, a minus 3 V threshold is a warning, because 3.3 V of drive over a 3 V threshold leaves almost nothing, and the part may never reach a usable resistance.
What 52 A means and what the pad can actually pass
At 4 milliohm and 52 A the conduction loss is 10.8 W. No 3 by 3 mm body dissipates 10.8 W in still air, whatever the pad, so the 52 A figure is a die and bond wire limit at a case temperature that only a heatsink or a very large copper plane can hold. The number that matters on a real board is the current at which the junction reaches its limit.
Work it backwards. A DFN 3 by 3 with an exposed pad soldered to 25 by 25 mm of two ounce copper, on a board with reasonable airflow, sits near 40 to 50 degrees per watt junction to ambient. A 100 C rise, from a 60 C ambient to a 160 C junction, therefore allows about 2 to 2.5 W. At 4 milliohm that is roughly 22 to 25 A continuous, and at 5 milliohm about 20 to 22 A. Those are respectable numbers for the body and they are half of the headline.
Pulsed duty changes the answer. A load switch that closes into a 200 A inrush for 100 microseconds is limited by the safe operating area, not by the steady thermal path, and the first thing to check is whether the data sheet publishes a single pulse curve for the die at the applied gate voltage. A reverse polarity application is different again, because the body diode conducts during the fault and the diode forward voltage, not the channel, sets the loss.
Where a P channel wins and where it does not
The case for this part is a high side switch above 20 V where the alternative is an N channel plus a charge pump plus a level shifter. Three components against one, and the one has a simpler failure mode. The case against it is efficiency at low gate drive and cost per milliohm, because P channel die area is expensive and the same 4 milliohm in N channel costs a fraction of it.
Our power management cross reference page sets out how a candidate is checked against an original before it is offered as a drop in, and this class of part is where that check earns its keep, because two P channels with the same headline resistance can differ by a factor of three in gate charge and by a volt in threshold.
The sourcing side of this part is covered on the pin to pin cross reference. For a 30 V P channel in a small body, the pinout, the gate window and the threshold decide whether a candidate can drop in.
Questions we get on this code
Can it be driven directly from a 3.3 V logic pin? Not reliably. A minus 3 V threshold leaves very little overdrive at 3.3 V, so the resistance is unpredictable and the part may sit in its linear region and heat. Use a small N channel to pull the gate down, or pick a part with a threshold nearer minus 1 V.
Is 30 V enough for a 24 V rail? Only with a clamp. A 24 V supply that rings 25 per cent reaches the rating exactly, and a P channel in a hot swap path sees the full input plus the cable inductance spike. A transient voltage suppressor across the input is the usual answer, and the part then runs at 30 V with margin rather than at the edge.
What should a purchase order carry? Part number, package, reel size and date code requirement. For a DFN 3 by 3 the reel is normally 3000 or 5000 pieces, and we confirm which one is on the offer rather than assuming it.
Do you hold stock on this part? We quote from what is confirmed at the time of the request. For a 30 V P channel the market is usually liquid, and the honest answer for a specific quantity comes back with the quotation.