VBQF1410
Product Specifications
VBQF1410
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF1410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF1410: 40 V and 28 A in a DFN 3 by 3
The VBQF1410 is a single N channel MOSFET rated at 40 V drain to source with a plus or minus 20 V gate window and a threshold of 1.8 V. It carries 28 A and its on resistance is 15 milliohm at a 4.5 V gate and 13 milliohm at 10 V. The die is trench silicon and the body is the DFN 3 by 3 with an exposed pad.
Forty volts, 15 milliohm and 28 A is a middle of the road switch, and that is its value. It sits between the 30 V parts that cannot survive a 24 V rail transient and the 60 V parts that cost twice the resistance for margin that the circuit does not need. On a 12 V or 24 V rail with a modest clamp it is the right class.
The threshold of 1.8 V means a 4.5 V drive gives 2.7 V of overdrive and a 3.3 V drive gives 1.5 V, which is workable but not generous. A 5 V driver is the comfortable pairing, and it is also where the published 15 milliohm applies.
Key data for the VBQF1410
| Configuration | Single N channel |
| Package | DFN 3 x 3 mm with exposed pad |
| VDS | 40 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V typical |
| ID | 28 A |
| RDS(on) at 4.5 V | 15 milliohm |
| RDS(on) at 10 V | 13 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, and in a buck it carries the inductor current during the dead time |
| Thermal path | Exposed pad at drain potential, copper island sets the rating |
Fifteen milliohm and the 24 V question
The 40 V rating covers a 24 V rail with 67 per cent of margin on paper, which is enough for a resistive load and not always enough for a switching one. A 24 V inductive load that is switched off produces whatever voltage the clamp allows, and a 40 V part with no clamp sees the full spike. The part is normally paired with a clamp or a freewheel diode, and that pairing is what makes 40 V workable on 24 V.
The resistance gap between the 4.5 V and 10 V columns is 15 per cent, which is small. That means the die was characterised with a 5 V drive as the primary condition, and a board that drives from 5 V gets nearly all of the performance. A 3.3 V drive is a different story: at 1.8 V threshold the overdrive is 1.5 V, and the resistance there is typically two to three times the published figure.
At 5 A the part drops 75 millivolt and dissipates 0.375 watt. At 10 A it is 1.5 watt, which the pad sheds on a normal island. At 20 A it is 6 watt and the part needs a thermal plane. The 28 A figure is a die limit at a 25 C case.
What a three millimetre body does to a board
The 3 by 3 body has a small pad, and the copper island around it is what carries the heat. A pad on four square centimetres with a via array gives a junction to ambient resistance around 45 degrees per watt, which handles 1.5 watt with a 70 degree rise. The same part with a minimal pad handles less than half of that.
The pad is the drain, and in a buck the drain is the switch node. The island is therefore a high frequency node with a significant area, and the loop from the input capacitor through the switch to ground has to be kept as short as the island allows. A large thermal island on the switch node and a small loop are in tension, and the resolution is to put the ground side of the loop on the layer below.
The gate return matters in a body this small. A gate trace that shares a path with the source current will lift the gate during a fast turn off, and at 28 A the source inductance is enough to do it. A separate return to the driver is the standard fix.
Choosing between 30 V, 40 V and 60 V in one body
The three voltage classes exist in the same DFN 3 by 3 body, and the choice between them is a margin against resistance trade that the board decides. Our kitting service page covers how the small switches and their gate parts are kitted when a product family carries more than one rail in the same body.
The screen is simple. If the highest voltage the drain ever sees is under 30 V, a 30 V part has lower resistance and should be preferred. If the load is inductive on a 24 V rail, a 40 V part with a clamp is the practical minimum. If the rail is a 48 V battery, none of these is right and the 100 V class in the same body takes over.
The sourcing side of this part is covered on the BOM scrubbing. For a board that carries several switches in one body size, that page covers how the bill of material is checked before release.
Questions we get on this code
Can it switch a 24 V inductive load? With a clamp or a freewheel diode, yes. Without one, the turn off spike decides, and 40 V has limited margin.
Is 28 A continuous? No. At 15 milliohm the continuous current in this body is 10 to 15 A with a good island, and 28 A is a die limit at a 25 C case.
Can it be driven from 3.3 V? It will turn on at 1.8 V threshold, but the resistance at 3.3 V is not published and is well above 15 milliohm. A 5 V driver is the intended condition.
How is it packed? DFN 3 by 3 normally ships 3000 or 5000 pieces on a large reel. We confirm the reel and the date code on the quotation.