Contact Us

VBP112MI75

Brand: VBsemi
VBsemi VBP112MI75 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP112MI75 — Discrete & Power Semiconductors | Superb Automation

VBP112MI75

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP112MI75 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP112MI75: a 1200 V IGBT with a diode in a TO247

The VBP112MI75 is an insulated gate bipolar transistor with a co-packaged fast recovery diode, rated at 1200 V collector to emitter with a plus or minus 30 V gate to emitter window. The threshold is 5.5 V, the saturation voltage is 1.55 V at a 15 V gate, and the continuous collector current is 75 A. The body is TO247 and the silicon is a field stop structure.

An IGBT is not a MOSFET and the difference matters at this voltage. Above about 600 V a MOSFET's on resistance rises faster than its area can grow, so a 1200 V MOSFET at 75 A would be a very large die with a resistance in the tens of milliohm and a body diode that is poor. An IGBT keeps a roughly constant saturation voltage instead, at the cost of a fixed forward drop of about 1.55 V that does not shrink with current.

That fixed drop is the whole trade. At 75 A the part dissipates 116 watt and needs a serious heatsink. At 20 A it dissipates 31 watt. At 5 A it still dissipates 7.75 watt, which is far more than a MOSFET of the same current would waste. So an IGBT is chosen for high voltage and high current together, not for small loads.

Key data for the VBP112MI75

Device typeIGBT with co-packaged fast recovery diode
PackageTO247, three lead through hole with tab
VCE1200 V
VGEPlus or minus 30 V
VGE threshold5.5 V typical
VCE(sat)1.55 V at a 15 V gate
IC75 A continuous
TechnologyField stop
DiodeCo-packaged fast recovery, which is what makes a bridge or an inverter practical
Gate drive15 V on, and a negative off bias is usual to prevent a false turn on
Thermal pathTab to heatsink, isolated or live
Short circuitThe catalogue page publishes no short circuit withstand time, so confirm it in the data sheet before a fault is relied on

Saturation voltage and the conduction loss it sets

At 1.55 V and 30 A the part dissipates 46.5 watt, and at 60 A it is 93 watt. Those numbers are independent of the gate voltage above about 12 V, because the device is saturated rather than resistive, so there is no benefit in driving the gate harder than the saturation knee.

The saturation voltage also has a positive temperature coefficient at high current, which is the property that makes paralleling possible: the hotter device takes less current. A MOSFET has the opposite behaviour near threshold and needs source resistors to parallel safely. That difference is one of the reasons an inverter at 1200 V uses IGBTs or silicon carbide rather than silicon MOSFETs.

The switching side is where the field stop structure earns its place. A trench field stop IGBT has a lower saturation voltage and a shorter tail current than an older planar part, and the tail current is the loss that a 1200 V device cannot avoid at turn off. The gate resistor sets the trade between tail loss and ringing, and it is chosen from the switching waveforms rather than from a table.

The co-packaged diode and the freewheel path

In a half bridge the diode carries the freewheel current when the opposite switch turns off. A fast recovery diode with a low forward drop is part of the device for a reason: the freewheel path is as much of the loss as the switch itself in a motor drive.

The diode's recovery charge is the number that decides the turn on loss of the opposite switch, because when that switch turns on it has to clear the diode's stored charge first. A part with a large recovery charge produces a current spike through both devices at every commutation, and at 1200 V that spike is both a loss and an EMI source. A snubber or a soft recovery diode helps, and a part with a better diode may be worth more than a part with a lower saturation voltage.

Buying a high voltage switch for a programme

Parts in this class are bought against a qualification and a lifetime, not against a spot price, because a change means a new thermal cycle test and possibly a new safety approval. Our OEM procurement page covers how a programme with a long life and a fixed bill of material is kept supplied.

The practical screen on an alternative is the diode recovery and the short circuit withstand, in that order. A part with the same saturation voltage and a weaker diode will run hotter in a bridge, and the difference only appears at the commutation edge, which a static test never shows.

The sourcing side of this part is covered on the supplier corrective action. For a device whose failure mode is thermal rather than electrical, that page covers how a non conformance is closed out.

Questions we get on this code

Can an IGBT replace a MOSFET directly? Only if the circuit is built for a fixed saturation drop and a tail current. The gate drive, the dead time and the thermal path all change.

Is 75 A continuous? At 1.55 V saturation that is 116 watt, which needs a heatsink sized for it. The current is real, but so is the heat.

What gate voltage is needed? 15 V on, and a negative off bias is normal to prevent a false turn on through the Miller capacitance.

What about the diode rating? The catalogue page states a co-packaged fast recovery diode without a separate current rating. Ask for the data sheet before relying on the diode for the full collector current.