VBL17R20S
Product Specifications
VBL17R20S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL17R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL17R20S: 700 V and 20 A with 210 milliohm
The VBL17R20S is a single N channel MOSFET in a TO263 body rated at 700 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 210 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy.
It sits one step above the 700 V 15 A part in this band in current and one step better in resistance, which is the whole reason two codes exist so close together. The pair is a choice between a smaller die and a lower loss at the same voltage, and the choice is made on the working current rather than on the label.
At 20 A the loss is 84 W, which no surface mount body removes. At 10 A it is 21 W and the package needs airflow. At 5 A it is 5.25 W and a good pad holds it. On a 680 V bus this is a part for a few amps with the voltage margin of a 600 V class plus one step.
Key data for the VBL17R20S
| Configuration | Single N channel |
| Package | TO263, surface mount with the tab on the drain |
| VDS | 700 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 20 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 210 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 5 A | 5.25 W at 210 milliohm |
| Loss at 10 A | 21 W at 210 milliohm |
| Loss at 20 A | 84 W at 210 milliohm |
| Gate charge | Not printed, ask for the curve at the working drain voltage |
Choosing between the two 700 V codes
The difference between 260 and 210 milliohm is a fifth of the resistance, which is a fifth of the conduction loss. On a 5 A load that is 1.25 W, which on a part making 5 W is a quarter of the heat. On a 2 A load it is 0.2 W and the choice stops mattering.
What the larger die costs is gate charge. A bigger die has more gate area, so the driver has to move more charge at every transition, and the transition loss rises. Where the converter runs at 40 kHz or more that cost can cancel the gain, which is why the smaller die is sometimes the better part at the same voltage and current.
The practical rule is to pick the resistance that brings the conduction loss to about half of what the board can remove, then leave the rest of the budget for switching. A part that uses the whole thermal budget on conduction has nothing left for the transition, and the transition is where a converter surprises its author.
Multiple epitaxy and the switching trade.
The multiple epitaxy structure builds the charge balance columns by stacking epitaxial layers, which gives a lower resistance per unit of breakdown voltage than a plain planar die and a body diode with a moderate recovery. It is the middle of the three processes in this band: slower than deep trench, cheaper than deep trench, and faster than planar.
Recovery of the body diode at 700 V and 10 A is worth a few watts in the opposite switch of a bridge leg. Below 30 kHz that is a manageable addition. Above it, a parallel silicon carbide diode is the usual fix, and its forward drop at low current is what decides whether it takes the current away from the body diode.
The output capacitance of the die stores energy that is lost at every turn on, so the loss scales with the square of the bus voltage and with the switching frequency. At 680 V and 40 kHz a die of this size loses a couple of watts in that path alone, which is why the frequency stays low on a rail this high.
Thermal path and creepage together
The tab carries the drain and sits at 680 V during the off state, so the copper island is a live node. It needs area for heat and distance for creepage, and those two pull against each other. A slot in the copper, a coated board or a smaller island with vias is how the two are balanced, and the choice depends on the humidity class the product claims.
At 5 A the loss is 5.25 W and a pad of a few square centimetres with vias holds it. At 8 A the loss is 13.4 W and the part wants airflow. The working continuous current on a two layer board is 4 to 6 A, and the number rises with copper thickness and with any airflow over the board.
Soldering is worth a word at this size. The tab has to be fully wetted for the thermal path to exist, and a void under the tab is a hot spot rather than a uniform rise. A reflow profile that holds the paste above liquidus long enough on a large thermal mass is the difference between a part that runs at 90 C and one that runs at 120 C on the same load.
Where the part fits and where it does not
It fits a 680 V bus start up circuit, an active clamp, an auxiliary supply on a 480 V drive, a photovoltaic string switch and a discharge path on a high rail. It does not fit a 20 A continuous load, a 690 V AC input without a clamp, or a high frequency bridge leg without an added diode.
For a part bought against a build that runs for years, the questions are the second source and the lead time rather than the data sheet. Our component lead time solutions page covers how a rail like this is planned rather than discovered at the last week.
The sourcing side of this part is covered on the power management cross reference. For a choice between two dies at one voltage, that page covers how the pair is compared on loss rather than on the label.
Questions we get on this code
Is it interchangeable with the 15 A 700 V part? On the footprint and the voltage, yes. It has less resistance and more gate charge, so the loss moves from conduction to switching as the frequency rises.
Can it be driven at 5 V? No. The threshold is 3.5 V and the resistance is published at 10 V. A 5 V drive puts it in the linear region.
Does it need a snubber? On a 680 V bus with 20 V of margin to the rating, yes. A small RC across the switch, close to the drain and source, keeps the turn off spike inside the rating.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.